MSDS Sheet 85351

• All Products
• Fasteners
   » Grade 8
   » Grade 5
   » Threaded Fasteners
• Hardware
• Rivet & Rivet Guns
• Vehicle Lighting
   » Cross Reference
• Electrical Products
• Tubing & Tube Fittings
• Air Brake Products
• Hose & Hose Ends
• Cutting Tools
• Abrasives
• Safety Products &
  Welding Supplies
• Chemicals & Paint
   » MSDS Information
   » CA/OTC Information
• Shop Supplies
• Vehicle Parts &
  Accessories
• Assortments &
  Steel Equipment
   » Assortment Listing

• Online Catalog Index
• Discontinued &
Overstock Specials

MATERIAL SAFETY DATA SHEET SECTION 1- PRODUCT AND COMPANY IDENTIFICATION PRODUCT NUMBER K1100404- PRODUCT NAME KRYLON Industrial IRON GUARD tm DTM Water-Based Anti-Rust Acrylic Coating, Gloss White MANUFACTURER'S NAME THE SHERWIN-WILLIAMS COMPANY KRYLON PRODUCTS GROUP Cleveland. OH 44115 Telephone numbers and websites Product information: (800) 247-3266 www.kpg-industrial.com Regulatory Information: (216) 566-2902 www.paintdocs.com Medical Emergency: (216) 566-2917 Transportation Emergency* (800) 424-9300 *for Chemical Emergency ONLY (spill, leak, fire, exposure, or accident) SECTION 2- COMPOSTITION/INFORMATION ON INGREDIENTS % by weight CAS Number Ingredient Units Vapor Pressure 18 13463-67-7 Titanium Dioxide ACGIH TLV 10 mg/m3 as dust OSHA PEL 10 mg/m3 total dust OSHA PEL 5 mg/m3 respirable fraction SECTION 3- HAZARDS IDENTIFICATION HMIS CODES Health 1* Flammability 0 Reactivity 0 ROUTES OF EXPOSURE INHALATION of vapor or spray mist. EYE or SKIN contact with the product, vapor or spray mist. EFFECTS OF OVEREXPOSURE EYES: Irritation SKIN: Prolonged or repeated exposure may cause irritation. INHALATION: Irritation of upper respiratory system. In a confined area vapors in high concentration may cause headache, nausea or dizziness. SIGNS AND SYMPTOMS OF OVEREXPOSURE Redness and itching or burning sensation may indicate eye or excessive skin exposure. MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE None generally recognized. CANCER INFORMATION For complete discussion of toxicology data refer to Section 11. SECTION 4- FIRST AID MEASURES EYES: Flush eyes with large amounts of water for 15 minutes. Get medical attention. SKIN: Wash affected area thoroughly with soap and water. Remove contaminated clothing and launder before re-use. INHALATION: If affected, remove from exposure. Restore breathing. Keep warm and quiet. INGESTION: Do Not induce vomiting. Get medical attention immediately. SECTION 5- FIRE FIGHTING MEASURES FLASH POINT LEL UEL FLAMMABILITY CLASSIFICATION Not Applicable n.a. n.a. Not Applicable EXTINGUISHING MEDIA Carbon Dioxide, Dry Chemical, Alcohol Foam UNUSUAL FIRE AND EXPLOSION HAZARDS Closed containers may explode (due to the build up of pressure) when exposed to extreme heat. During emergency conditions overexposure to decomposition products may cause a health hazard. Symptoms may not be immediately apparent. Obtain medical attention. SPECIAL FIRE FIGHTING PROCEDURES Full protective equipment including self-contained breathing apparatus should be used. Water spray may be ineffective. If water is used, fog nozzles are preferable. Water may be used to cool closed containers to prevent pressure build-up and possible autoignition or explosion when exposed to extreme heat. SECTION 6- ACCIDENTAL RELEASE MEASURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED - Remove all sources of ignition. Ventilate the area. - Remove with inert absorbent. SECTION 7- HANDLING AND STORAGE STORAGE CATEGORY Not Applicable PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE Keep container closed when not in use. Transfer only to approved containers with complete and appropriate labeling. Do not take internally. Keep out of the reach of children. SECTION 8- EXPOSURE CONTROLS/PERSONAL PROTECTION PRECAUTIONS TO BE TAKEN IN USE Use only with adequate ventilation. Avoid contact with eyes. Avoid breathing in vapor spray and mist. Wash hands after using. This coating may contain materials classified as nuisance particulates (listed as "dust" in Section 2) which may be present at hazardous levels only during sanding or abrading of the dried film. If no specific dusts are listed in section 2, the applicable limits for nuisance dusts are ACGIH TLV 10 mg/m3(total dust), 3 mg/m3 (respirable fraction) OSHA PEL 15 mg/m3 (total dust) 5mg/m3 (respirable fraction). VENTILATION Local exhaust preferable. General exhaust acceptable if the exposure to materials in Section 2 is maintained below applicable exposure limits. Refer to OSHA Standards 1910.94, 1910.107 and 1910.108. RESPIRATORY PROTECTION If personal exposure cannot be controlled below applicable limits by ventilation, wear a properly fitted organic vapor/particulate respirator approved by NIOSH/MSHA for protection against materials in Section 2. When sanding or abrading the dried film, wear a dust/mist respirator approved by NIOSH/MSHA for dust which may be generated from this product, underlying paint, or the abrasive. PROTECTIVE GLOVES Wear gloves which are recommended by glove supplier for protection against materials in Section 2. EYE PROTECTION Wear safety spectacles with unperforated sidesheilds. SECTION 9- PHYSICAL AND CHEMICAL PROPERTIES PRODUCT WEIGHT 9.81 lb/gal 1175 g/l SPECIFIC GRAVITY 1.18 BOILING POINT 212-369'f 100-187'c MELTING POINT Not Available VOLATILE VOLUME 64% EVAPORATION RATE Slower than ether VAPOR DENSITY Heavier than Air SOLUBILITY IN WATER N.A. pH 9.0 VOLATILE ORGANIC COMPOUNDS (VOC Theoretical-as packaged) 0.82lb/gal 99g/l Less water and federally exempt solvents 0.32 lb/gal 39g/l Emitted VOC SECTION 10- STABILITY AND REACTIVITY STABILITY-Stable CONDITIONS TO AVOID None Known INCOMPATIBILITY None Known HAZARDOUS DECOMPOSITION PRODUCTS By fire: Carbon Dioxide, Carbon Monoxide HAZARDOUS POLYMERIZATION Will not occur. SECTION 11- TOXICOLOGICAL INFORMATION CHRONIC HEALTH HAZARDS IARC's Monograph No. 93 reports there is sufficient evidence of carcinogenicity in experimental rats exposed to titanium dioxide but inadequate evidence for carcinogenicity in humans and has assigned a group 2b rating. In addition, the IARC summary concludes, "No significant exposure to titanium dioxide is thought to occur during the use of products in which titanium is bound to other materials, such as paint. TOXICOLOGY DATA CAS No. INGREDIENT NAME 13463-67-7 Titanium Dioxide LC50 RAT 4HR Not Available LD50 RAT Not Available SECTION 12- ECOLOGICAL INFORMATION ECOTOXOCOLOGICAL INFORMATION No data available SECTION 13- DISPOSAL CONSIDERATIONS WASTE DISPOSAL METHOD Waste from this product is not hazardous as defined under the Resource Conservation and Recovery Act (RCRA) 40 CFR 261. Incinerate in approved facility. Do not incinerate closed container. Dispose of in accordance with Federal, State/Provincial and local regulations regarding pollution. SECTION 14- TRANSPORT INFORMATION US GROUND (DOT) Not Regulated for Transportation CANADA (TGD) Not Regulated for Transportation IMO Not Regulated for Transportation SECTION 15- REGULATORY INFORMATION SARA 313 (40 CFR 372.65C) SUPPLIER NOTIFICATION CAS No. CHEMICAL/COMPOUND % BY WEIGHT % BY ELEMENT No ingredients in this product are subject to Sara 313 (40 cfr 372.65c) Supplier Notification. CALIFORNIA PROPOSITION 65 WARNING: This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm. TSCA CERTIFICATION All chemicals in this product are listed, or are exempt from listing, on the TSCA Inventory. SECTION 16- OTHER INFORMATION This product has been classified in accordance with the hazard criteria of the Canadian Controlled Products Regulations (CPR) and the MSDS contains all of the information required by the CPR. The above information pertains to this product as currently formulated and is based on the information available at this time. Addition of reducers or other additives to this product may substantially alter the composition and hazards of the product. Since conditions of use are outside our control, we make no warranties, expressed or implied, and assume no liability in connection with any use of this information.