MSDS 82129

Cookson Electronics                          Alpha Metals
A Division of Cookson Group psl              600 Route 440
Revised  6/16/00                             Jersey City, NJ 07304
Replaces (None)                              (201) 434-6778
Printed 1/10/05                              (201) 434-7508 fax
MSDS ID:  FC 00108407                                                            
www.alphametals.com 

 
                            MATERIAL SAFETY DATA SHEET

 
                  1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

 
PRODUCT NAME:  AM HEAT SHIELD 6 X 8   56850
 
MANUFACTURER'S NAME:  ALPHA METALS, INC
ADDRESS:              600 ROUTE 440
                      JERSEY CITY, NJ  07304
TRANSPORT EMERGENCY #: CHEMTREC; 1-800-424-9300 
 
BUSINESS PHONE:  1-201-434-6778
 

                  2.  INGREDIENT AND EXPOSURE LIMIT INFORMATION

 
CHEMICAL NAME       CAS #           % W/W           OSHA       PEL - TWA
--------------------------------------------------------------------------------
NO OSHA HAZARDOUS
COMPONENTS
 

                            3.  HAZARDS IDENTIFICATION

 
EMERGENCY OVERVIEW:  NO EYE HAZARD
 
HMIS RATING SYSTEM:
Health:         Flammability:      Reactivity: 0        Protection: B
 
NFPA RATING SYSTEM:
 
IMMEDIATE (ACUTE) SYMPTOMS OVER-EXPOSURE BY ROUTE OF EXPOSURE:
INHALATION:       NO HAZARD IN NORMAL INDUSTRIAL USE.
EYES:             NO HAZARD IN NORMAL INDUSTRIAL USE.
SKIN CONTACT;     NO HAZARD IN NORMAL INDUSTRIAL USE.
SKIN ABSORPTION;  NO ABSORPTION HAZARD IN NORMAL INDUSTRIAL 
                  USE. 
INGESTION:        NO HAZARD IN NORMAL INDUSTRIAL USE. 
 
LONG TERM (CHRONIC) HEALTH EFFECTS:
CARCINOGENICITY: NONE OF THE SUBSTANCES HAVE BEEN SHOWN TO
                 CAUSE CANCER IN LONG TERM ANIMAL STUDIES.
                 NOT A CARCINOGEN ACCORDING TO NTP, IARC, OR
                 OSHA. 
REPRODUCTION;     NO DATA AVAILABLE TO INDICATE PRODUCT OR ANY
                  COMPONENTS PRESENT AT GREATER THAN 0.1% MAY
                  CAUSE BIRTH DEFECTS. WOMEN OF CHILD BEARING 
                  AGE SHOULD AVOID EXPOSURE TO LEAD AND ITS
                  INORGANIC COMPOUNDS DUE TO POST-NATAL EFFECTS
 

                              4.  FIRST AID MEASURES

 
SKIN EXPOSURE:     WASH WITH SOAP AND WATER.
EYE EXPOSURE:       NONE EXPECTED TO BE NEEDED, HOWEVER, USE AN
                    EYE WASH TO REMOVE A CHEMICAL FROM YOUR EYE
                    REGARDLESS OF THE LEVEL OF HAZARD. 
 
INHALATION:   THIS MATERIAL DOES NOT PRESENT A HAZARD IF
              INHALED. REMOVE INDIVIDUAL TO FRESH AIR AFTER
              AN AIRBORNE EXPOSURE IF ANY SYMPTOMS DEVELOP,
              AS A PRECAUTIONARY MEASURE. 
INGESTION:    NO HAZARD IN NORMAL INDUSTRIAL USE. DO NOT 
              INDUCE VOMITING. SEEK MEDICAL ATTENTION IF
              SYMPTOMS DEVELOP. PROVIDE MEDICAL CARE
              PROVIDER WITH THIS MSDS. 
 

                            5.  FIRE FIGHTING MEASURES

 
FLASH POINT:               N/A  DEG. C
AUTOIGNITION TEMPERATURE:  N/E DEG. C
EXPLOSIVE LIMITS % IN AIR: N/E  
FIRE FIGHTING METHODS:     WILL NOT BURN, NO SPECIAL
                           INSTRUCTIONS AVAILABLE. 
                           USE METHODS APPROPRIATE FOR
                           SURROUNDING  MATERIALS. 
 

                         6.  ACCIDENTAL RELEASE MEASURES

 
METHODS FOR CLEAN-UP:   NO SPECIAL SPILL CLEAN-UP
                        CONSIDERATIONS. COLLECT AND DISCARD
                        IN REGULAR TRASH. 
 

                            7.  HANDLING AND STORAGE:

 
HANDLING MEASURES:   NO SPECIAL HANDLING INSTRUCTIONS DUE TO
                     TOXICITY.
STORAGE MEASURES:    NO SPECIAL REQUIREMENTS
 

                   8. EXPOSURE CONTROLS AND PERSONAL PROTECTION

 
ENGINEERING MEASURES;  NO ENGINEERING CONTROLS ARE LIKELY TO 
                       BE REQUIRED TO MAINTAIN OPERATOR 
                       COMFORT UNDER NORMAL CONDITIONS OF USE.
 
RESPIRATORY PROTECTION;  NO RESPIRATORY PROTECTION REQUIRED 
                         UNDER NORMAL CONDITIONS OF USE. 
EYE PROTECTION:  NO SPECIAL REQUIREMENTS UNDER NORMAL
                 INDUSTRIAL USE. 
SKIN PROTECTION: NOT NORMALLY CONSIDERED A SKIN HAZARD. 
                 WHERE USE CAN RESULT IN SKIN CONTACT, 
                 PRACTICE GOOD PERSONAL HYGIENE. WASH
                 HANDS AND OTHER EXPOSED AREAS WITH MILD
                 SOAP AND WATER BEFORE EATING, DRINKING, 
                 AND WHEN LEAVING WORK. 
CONTROL PARAMETERS: ACGIH EXPOSURE LIMITS

CHEMICAL NAME                TLV-TWA            STEL               CEILING
--------------------------------------------------------------------------------
NO OSHA HAZARDOUS COMPONENTS
 

                       9.  PHYSICAL AND CHEMICAL PROPERTIES

 
ODOR;                        NONE
pH:                          N/A
SPECIFIC GRAVITY:            1.0000
VAPOR PRESSURE, mm Hg at 20C:
MELTING POINT or RANGE  ©:
BOILING POINT  ©:
 

                          10.  STABILITY AND REACTIVITY

 

                          11.  TOXICOLOGICAL INFORMATION

 
COMPONENT TOXICOLOGY DATA  (NIOSH)
CHEMICAL NAME               LD50/LC50
 

                           12.  ECOLOGICAL INFORMATION

 

                           13.  DISPOSAL CONSIDERATIONS


 
                            14.  TRANSPORT INFORMATION


 
                           15.  REGULATORY INFORMATION

 
TSCA STATUS:    ALL COMPONENTS OF THIS PRODUCT ARE LISTED ON
                THE TSCA INVENTORY OF EXISTING CHEMICAL
                SUBSTANCES. 
REGULATED CHEMICALS:
 
CHEMICAL NAME                                                               
REGULATION
NO SARA 313 CHEMICAL
 
CERCLA REGULATED CHEMICALS AND REPORTABLE QUANTITY (RQ):
 

                              16.  OTHER INFORMATION

 
The information contained herein is based on data considered accurate. However, 
no warranty is expressed or implied regarding the accuracy of the data or the 
results to be obtained from the use thereof. Additionally, Alpha Metals, Inc. 
assumes no responsibility for injury to the vendee or third persons proximately 
caused by the material even if reasonable safety procedures are followed. 
Furthermore, vendee assumes the risk in his use of the material. 

The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance.

© 2008 Imperial Supplies LLC Questions or comments? Contact us.