Start an Order |
|
|
|
| Start an Order |
|||
| Home > Products > Chemicals & Paint > MSDS Sheets > MSDS 73772 -- [Back] | |||
|
MSDS 73772 73772: 3M Hookit Sand Disc 6"-320G [50]MSDS Last updated: 12/15/2009
MATERIAL SAFETY DATAT SHEET 3M Abrasive Products, 334U, 735U, 3M Imperial
Hookit II Discs 05/11/09 | |
3M
Material Safety Data Sheet
Copyright, 2009, 3M Company. All rights reserved. Copying and/or
downloading of this information for the purpose of properly utilizing 3M
products is allowed provided that: (1) the information is copied in full
with no changes unless prior written agreement is obtained from 3M, and
(2) neither the copy nor the original is resold or otherwise distributed
with the intention of earning a profit thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M Abrasive Products, 334U,3M
Imperial Hookit II Discs
MANUFACTURER: 3M
DIVISION: Abrasives Systems Division
ADDRESS: 3M CENTER
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 05/11/09
Supercedes Date: 05/11/09
Document Group: 16-4680-1
Product Use:
Intended Use: Abrasive Product
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
Aluminum Oxide Mineral 1344-28-1 5-35
Paper Backing None 30-70
Cured Adhesive None 5-30
Antiloading Agent 1592-23-0 1-10
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: Solid abrasive product, no odor.
These products may include Stikit,
Hookit or Hookit II attachment
systems.
General Physical Form: Solid
Immediate health, physical, and This document covers only the 3M
environmental hazards: product. For complete assessment,
when determining the degree of
hazard, the material being abraded
must also be considered.
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Mechanical Eye Irritation: Signs/symptoms may include redness, tearing,
and corneal abrasion.
Dust created by cutting, grinding, sanding or machining may cause eye
irritation. Signs/symptoms may include redness, swelling, pain, tearing,
and blurred or hazy vision.
Skin Contact:
Mechanical Skin irritation: Signs/symptoms may include abrasion,
redness, pain and itching.
Inhalation:
Dust from cutting, grinding, sanding or machining may cause irritation
of the respiratory system. Signs/symptoms may include cough, sneezing,
nasal discharge, headache, hoarseness, and nose and throat pain.
Ingestion:
No health effects are expected.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that
appropriate personal and industrial hygiene practices are followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms
persist get medical attention.
Skin Contact: Wash affected area with soap and water. If signs/symptoms
develop get medical attention.
Inhalation: Remove person to fresh air. If signs/symptoms develop, get
medical attention.
If Swallowed: No need for first aid is anticipated.
SECTION 5: FIRE FIGHTING MEASRES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits-LEL Not Applicable
Flammable Limits-UEL Not Applicable
5.2 EXTINGUISHING MEDIA
Ordinary combustible material. Use fire extinguishers with class A
extinguishing agents (e.g., water, foam).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Wear full protective equipment (Bunker
Gear) and a self-contained breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Not applicable. None inherent in
this product.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion
and thermal decomposition information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Not applicable.
In the event of a release of this material, the user should determine if
the release qualifies as reportable according to local, state, and
federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
For industrial or professional use only. Avoid breathing of dust created
by sanding, grinding or machining. Damaged product can break apart
during use and cause serious injury to face or eyes. Check product for
damage such as cracks or nicks prior to use. Replace if damaged. Always
wear eye and face protection when working at sanding or grinding
operations or when near such operations. Sparks and particles flying
from the product during sanding or grinding can cause injury and fire.
7.2 STORAGE
Store in a cool, dry place.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Use with appropriate local exhaust ventilation. Use general dilution
ventilation and/or local exhaust ventilation to control airborne
exposure to below Occupational Exposure Limits and/or control dust,
fumes, or airborne particles. If ventilation is not adequate, use
respiratory protection equipment. Provide appropriate local exhaust
ventilation if sanding, grinding or machining.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact. To minimize the risk of injury to face and eyes,
always wear eye and face protection when working at sanding or grinding
operation or when near such operations.
8.2.2 Skin Protection
Avoid skin contact. Wear appropriate gloves to minimize risk of injury
to skin from contact with dust or physical abrasion from grinding or
sanding.
8.2.3 Respiratory Protection
Avoid breathing of dust created by sanding, grinding or machining.
Assess exposure concentrations of all materials involved in the work
process. Consider material being abraded when determining the
appropriate respiratory protection. Select and use appropriate
respirators to prevent inhalation overexposure.
8.2.4 Prevention of Swallowing
Wash hands after handling and before eating. Not an expected route of
exposure.
8.3 EXPOSURE GUIDELINES
Ingredient Authority Type Limit Additional
Information
Aluminum Oxide ACGIH TWA, 10 mg/m3 Table A4
Mineral particulate
matter, <1%
Aluminum Oxide CMRG TWA 1 fiber/cc
Mineral
Aluminum Oxide OSHA TWA, 5 mg/m3 Table Z-1
Mineral respirable
Aluminum Oxide OSHA TWA, Vacated 10 mg/m3
Mineral as dust
Aluminum Oxide OSHA TWA, as 15 mg/m3 Table Z-1
Mineral total dust
STERATES ACGIH TWA, as 10 mg/m3 Table A4
total dust
VAC Vacated PEL: Vacated Permissible Exposure Limits [PEL] are enforced
as the OSHA PEL in some states. Check with your local regulatory agency.
SOURCE OF EXPOSURE LIMIT DATA
ACGIH: American Conference of Governmental
Industrial Hygienists
CMRG: chemical Manufacturer Recommended
Guideline
OSHA: Occupational Safety and Health
Administration
AIHA: American Industrial Hygiene
Association Workplace Environmental
Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Odor, Color, Grade: Solid abrasive product, no odor.
These products may include Stikit,
Hookit or Hookit II attachment
systems.
General Physical Form: Solid
autoignition temperature: Not Applicable
Flash Point Not Applicable
Flammable Limits-LEL Not Applicable
Flammable Limits-UEL Not Applicable
Boiling point Not Applicable
Vapor Density Not Applicable
Vapor Pressure Not Applicable
Specific Gravity Not Applicable
pH Not Applicable
Melting point Not Applicable
Solubility in Water Not Applicable
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable
Materials and Conditions to Avoid: Not Applicable
Hazardous Polymerization: Hazardous Polymerization will not occur.
Hazardous Decomposition or by-Products
Substance Condition
Carbon Monoxide During Combustion
Carbon Dioxide During Combustion
Hazardous Decomposition: Under recommended usage conditions, hazardous
decomposition products are not expected. Hazardous decomposition
products may occur as a result of oxidation, heating, or reaction with
another material.
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for
Toxicological information on this material and/or its components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMCAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: The substate that was abraded must be considered
as a factor in the disposal method for this product. Dispose of waste
product in a sanitary landfill. As a disposal alternative, incinerate in
an industrial or commercial facility.
Since regulations vary, consult applicable regulations or authorities
before disposal.
SECTION 14: TRANSPORT INFORMATION
Please contact the emergency numbers listed on the first page of the
MSDS for Transportation Information for this material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard-No Pressure Hazard-No Reactivity Hazard-No Immediate
Hazard-Yes Delayed Hazard-No
STATE REGULATIONS
Contact 3M for more information.
CHEMICAL INVENTORIES
This product is an article as defined by TSCA regulation, and is exempt
from TSCA Inventory listing requirements.
Contact 3M for more information.
INTERNATIONAL REGULATIONS
Contact 3M for more information.
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health:1 Flammability: 0 Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed
for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions
of fire, spill or similar emergencies. Hazard ratings are primarily
based on the inherent physical and toxic properties of the material but
also include the toxic properties of combustion or decomposition
products that are know to be generated in significant quantities.
Reason for Reissue: The MSDS has been revised because 3M has adopted the
16-section ANSI/ISO format. The potential hazards of the product have
not changed. We encourage you to reread the MSDS and review the
information.
Revision Changes:
Section 1: Product name was modified
Page Heading: Product name was modified.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is
believed to be correct as of the date issued. 3M MAKES NO WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR
COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for
determining whether the 3M product is fit for a particular purpose and
suitable for user's method of use or application. Given the variety of
factors that can affect the use and application of a 3M product, some of
which are uniquely within the user's knowledge and control, it is
essential that the user evaluate the 3M product to determine whether it
is fit for a particular purpose and suitable for user's method of use or
application.
3M provides information in electronic form as a service to its
customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information,
3M makes no representations as to its completeness or accuracy. In
addition, information obtained from a database may not be as current as
the information in the MSDS available directly from 3M.
3M MSDS are available at www.3M.com
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance. For more product information by email, click here Imperial Supplies LLC does not provide services and products outside the United States |
