MSDS 73615

MATERIAL SAFETY DATA SHEET 3M  Scotch-Brite Clean & Strip XT Products   
and Brake Hub Cleaning Discs 01/30/2009                                 

3M

Material Safety Data Sheet

Copyright, 2009, 3M Company. All rights reserved. Copying and/or        
downloading of this information for the purpose of properly utilizing 3M
products is allowed provided that: (1) the information is copied in full
with no changes unless prior written agreement is obtained from 3M, and 
(2) neither the copy nor the original is resold or otherwise distributed
with the intention of earning a profit thereon.                         
                                                                        

SECTION 1: PRODUCT AND COMPANY IDENTIFICATION                           
                                                                        
PRODUCT NAME:      3M Scotch-Brite Clean & Strip XT Products and Brake  
                   Hub Cleaning Discs                                   
MANUFACTURER:      3M                                                   
DIVISION:          Abrasives Systems Division                           
                                                                        
ADDRESS:           3M Center                                            
                   St. Paul, MN 55144-1000                              

EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)  

Issue Date:          01/30/2009                                               
Supercedes Date:     07/26/2006                                               
                                                                              
Document Group:      21-6126-3                                                

Product Use:                                                                  
   Intended Use:        Abrasive Product                                        


SECTION 2: INGREDIENTS                                                  

Ingredient                  C.A.S. No.         % by Wt                        
Silicon Carbide Mineral     409-21-2           30-50                          
Nylon Fiber                 25038-54-4         10-30                          
Cured Resin                 Mixture            10-25                          
Roloc TN, TP, TR, or TS     None               0-5                            
Attachment                                                                    
Roloc  Adhesive             Mixture            0-3                            
Quartz Silica               14808-60-7         0.06-0.24                      
                                                                              

SECTION 3: HAZARDS IDENTIFICATION                                       

3.1 EMERGENCY OVERVIEW
Odor, Color, Grade:             Solid Abrasive Product,                 
General Physical Form           Solid                                   

Immediate health, physical, and This document covers only the 3M        
environmental hazards:          product. For complete assessment, when  
                                determining the degree of hazard, the   
                                material being abraded must also be     
                                considered.                             
                                                                        
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:                                                            
Mechanical eye irritation: Signs/symptoms may include pain, redness,    
tearing and corneal abrasion.                                           

Dust created by cutting, grinding, sanding, or machining may cause eye  
irritation. Signs/symptoms may include redness, swelling, pain, tearing,
and blurred or hazy vision.                                             

Skin Contact:                                                           
Mechanical Skin irritation: Signs/symptoms may include abrasion,        
redness, pain, and itching.                                             

Inhalation:                                                             
Dust from cutting, grinding, sanding or machining may cause irritation  
of the respiratory system. Signs/symptoms may include cough, sneezing,  
nasal discharge, headache, hoarseness, and throat pain.                 

Prolonged or repeated exposure may cause:                               
Pneumoconiosis: Sign/symptoms may include persistent cough,             
breathlessness, chest pain, increased amounts of sputum, and changes in 
lung function tests.                                                    

Ingestion:                                                              
No health effects are expected.                                         
                                                                        
This product contains quartz silica. Cancer of the lungs and silicosis  
have been associated with quartz (crystalline) silica. No exposure to   
quartz (crystalline) silica is anticipated during normal intended use of
3M Coated Abrasives and Surface Conditioning Abrasives. No detectable   
respirable quartz and other forms of crystalline silica were found when 
a simulated grinding air sampling study was conducted on analogous      
coated and surface conditions abrasive constructions that contained     
similar to or greater concentrations of crystalline silica. Therefore,  
the health effects associated with crystalline silica (e.g. quartz) are 
not expected during the intended use of this product.                   
                                                                        
Ingredient       C.A.S No.      Class Description       Regulation       
Quartz Silica    14808-60-7     Group 1                 International Agency
                                                        for Research on Cancer
Quartz Silica    14808-60-7     Known human carcinogen  National Toxicology
                                                        Program Carcinogens
                                                                        

SECTION 4: FIRST AID MEASURES                                           

4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that
appropriate personal and industrial hygiene practices are followed.

Eye Contact:     Flush eyes with large amounts of water. If             
                 signs/symptoms persist, get medical attention.         
Skin Contact:    Wash affected area with soap and water. If             
                 signs/symptoms develop, get medical attention.         
Inhalation:      Remove person to fresh air. If signs/symptoms develop, 
                 get medical attention.                                 
If Swallowed:    No need for first aid is anticipated.                  


SECTION 5: FIRE FIGHTING MEASURES                                       

5.1 FLAMMABLE PROPERTIES
Autoignition temperature   Not Applicable                                 
Flash Point                Not Applicable                                 
Flammable Limits-LEL       Not Applicable                                 
Flammable Limits-UEL       Not Applicable                                 

5.2 EXTINGUISHING MEDIA
Ordinary combustible material. Use fire extinguishers with class A
extinguishing agents (e.g., water, foam).

5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting         Wear full protective equipment (Bunker   
Procedures:                   Gear) and a self-contained breathing     
                              apparatus (SCBA).                        
Unusual Fire and Explosion    Not applicable. None inherent in this    
Hazards:                      product.                                 

Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion
and thermal decomposition information.                                  


SECTION 6: ACCIDENTAL RELEASE MEASURES                                  

Accidental Release Measures: Not applicable.

In the event of a release of this material, the user should determine if
the release qualifies as reportable according to local, state, and      
federal regulations.                                                    


SECTION 7: HANDLING AND STORAGE                                         

7.1 HANDLING
For industrial or professional use only. Avoid breathing of dust created by
sanding, grinding or machining. Avoid eye contact with dust or airborne
particles. Damaged product can break apart during use and
cause serious injury to face or eyes. Check product for damage such as cracks
or nicks prior to use. Replace if damaged. Always wear eye and face protection
when working at or sanding or grinding operations or when near such operations.
Sparks and particles flying from the product during sanding or grinding can
cause injury and fire.

7.2 STORAGE
Store in a cool, dry place.


SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION                        

8.1 ENGINEERING CONTROLS
Provide appropriate local exhaust ventilation for sanding, grinding or
machining. Provide ventilation adequate to control dust concentrations below
recommended exposure limits and/or control dust.  Use general dilution
ventilation and/or local exhaust ventilation to
control airborne exposures to below Occupational Exposure Limits and/or control
dust, fume, or airborne particles. If ventilation is not adequate, use
respiratory protection equipment.

8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact. To minimize the risk of injury to face and eyes, always wear
eye and face protection when working at sanding or grinding operations or when
near such operations.
The following eye protection(s) are recommended: Safety Glasses with side
                                                 shields.

8.2.2 Skin Protection
Avoid skin contact. Wear appropriate gloves to minimize risk of injury to skin
from contact with dust or physical abrasion from grinding or sanding.

8.2.3 Respiratory Protection
Avoid breathing of dust created by sanding, grinding or machining. Assess
exposure concentrations of all materials involved in the work process. Consider
material being abraded when determining the appropriate respiratory protection.
Select and use appropriate respirators to prevent inhalation overexposure.
Select one of the following NIOSH approved respirators based on airborne
concentration of contaminants and in accordance with OSHA regulations: Half
face piece or full-face air-purifying respirator with N95 particulate filters.
Consult the current 3M Respiratory Selection Guide for additional information
or call 1-800-243-4630 for 3M technical assistance.

8.2.4 Prevention of Swallowing
Not an expected route of exposure. Wash hands after handling and before eating.

8.3 EXPOSURE GUIDELINES
Ingredient               Authority Type              Limit        Additional 
                                                                  Information
Quartz Silica            ACGIH     TWA, respirable   0.025 mg/m3  Table A2    
Quartz Silica            OSHA      TWA, respirable   0.1 mg/m3    Table Z-1A 
Silicon Carbide Mineral  ACGIH     TWA, as fibrous   0.1 fiber/cc Table A2   
                                   forms, including                          
                                   whiskers                                  
Silicon Carbide Mineral  ACGIH     TWA, as           3 mg/m3                   
                                   non-fibrous,respirable                    
Silicon Carbide Mineral  ACGIH     TWA, as           10 mg/m3                 
                                   non-fibrous,                              
                                   inhalable fraction                        
Silicon Carbide Mineral  OSHA      TWA, respirable   5mg/m3       Table Z-1  
Silicon Carbide Mineral  OSHA      TWA, Vacated, as  10mg/m3                 
                                   dust                                      
Silicon Carbide Mineral  OSHA      TWA, as total     15mg/m3      Table Z-1  
                                   dust                                      

VAC Vacated PEL: Vacated Permissible Exposure Limits [PEL] are enforced as the
OSHA PEL in some states. Check with your local regulatory agency.

SOURCE OF EXPOSURE LIMIT DATA:
ACGIH            American Conference of Governmental
                 Industrial Hygienists              
CMRG:            Chemical Manufacturer Recommended  
                 Guideline                          
OSHA:            Occupational Safety and Health     
                 Administration                     
AIHA:            American Industrial Hygiene        
                 Association Workplace Environmental
                 Exposure Level (WEEL)              


SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES                             

Odor, Color, Grade:                 Solid Abrasive Product             
General Physical Form:              Solid                              
Autoignition temperature            Not Applicable                     
Flash Point                         Not Applicable                     
Flammable Limits-LEL                Not Applicable                     
Flammable Limits-UEL                Not Applicable                     
Boiling point                       Not Applicable                     
Vapor Density                       Not Applicable                     
Vapor Pressure                      Not Applicable                     
Specific Gravity                    Not Applicable                     
pH                                  Not Applicable                     
Melting point                       Not Applicable                     
Solubility In Water                 Not Applicable                     


SECTION 10: STABILITY AND REACTIVITY                                    

Stability: Stable.
Materials and Conditions to Avoid: Not applicable
Hazardous Polymerization: Hazardous Polymerization will not occur.

Hazardous Decomposition or By-Products
Substance             Condition                                         
Carbon monoxide       During Combustion                                 
Carbon dioxide        During Combustion                                 

Hazardous Decomposition: Under recommended usage conditions, hazardous
decomposition products are not expected. Hazardous decomposition products may
occur as a result of oxidation, heating, or reaction with another material.


SECTION 11: TOXICOLOGICAL INFORMATION                                   

Please contact the address listed on the first page of the MSDS for     
Toxicological Information on this material and/or its components.       


SECTION 12; ECOLOGICAL INFORMATION                                      

ECOTOXICOLOGICAL INFORMATION
Not determined.

CHEMICAL FATE INFORMATION
Not determined.


SECTION 13: DISPOSAL CONSIDERATIONS                                     

Waste Disposal Method: The substrate that was abraded must be considered as a
factor in the disposal method for this product. Dispose of waste product in a
sanitary landfill. As a disposal alternative, incinerate in an industrial or
commercial facility 

EPA Hazardous Waste Number (RCRA): Not regulated

Since regulations vary, consult applicable regulations or authorities   
before disposal.                                                        


SECTION 14: TRANSPORT INFORMATION                                       

Not regulated per U.S. DOT, IATA or IMO.

These transportation classifications are provided as a customer service.
As the shipper YOU remain responsible for complying with all applicable 
laws and regulations, including proper transportation classification and
packaging. 3 M's transportation classifications are based on product    
formulation, packaging, 3 M policies and 3 M's understanding of         
applicable current regulations. 3 M does not guarantee the accuracy of  
this classification information. This information applies only to       
transportation classification and not the packaging, labeling, or       
marking requirements. The original 3 M package is certified for U.S.    
ground shipment only. If you are shipping by air or ocean, the package  
may not meet applicable regulator requirements.                         
                                                                        

SECTION 15: REGULATORY INFORMATION                                      
                                                                        
US FEDERAL REGULATIONS
Contact 3 M for more information.

311/312 Hazard Categories:
Fire Hazard-No Pressure Hazard-No Reactivity Hazard-No Immediate Hazard-Yes
Delayed Hazard-Yes

STATE REGULATIONS
Contact 3M for more information.

CHEMICAL INVENTORIES
This product is an article as defined by TSCA regulations, and is exempt from
TSCA Inventory listing requirements.

Contact 3M for more information.

INTERNATIONAL REGULATIONS
Contact 3M for more information.


This MSDS has been prepared to meet the U.S. OSHA Hazard Communication  
Standard, 29 CFR 1910.1200.                                             


SECTION 16: OTHER INFORMATION                                           

NFPA Hazard Classification
Health: 1     Flammability: 1    Reactivity: 0   Special Hazards: None 

National Fire Protection Association (NFPA) hazard ratings are designed for use
by emergency response personnel to address the hazards that are presented by
short-term, acute exposure to a material under conditions of fire, spill, or
similar emergencies. Hazard ratings are primarily based on the inherent
physical and toxic properties of the material but also include the toxic
properties of combustion or decomposition products that are known to be
generated in significant quantities.

Revision Changes:                                                       
Section 1:          Product name was modified.                          
Section 1:          Product use information was modified.               
Section 16:         NFPA hazard classification for flammability was     
                    modified.                                           
                    Copyright was modified.                                   
Section 7:          Handling information was modified.                  
Section 8:          Engineering controls information was modified.      
Section 8:          Skin protection phrase was modified.                
Section 8:          Respiratory protection information was modified.    
Section 8:          Prevention of swallowing information was modified.  
Section 14:         Transportation legal text was modified.             
                    Page Heading: Product name was modified.                    
Section 15:         311/312 Delayed Hazard score was modified.          
Section 1:          Initial issue message was modified.                 
Section 3:          Carcinogenicity comment was added.                  
Section 13:         EPA hazardous waste number (RCRA) heading was added.
Section 13:         EPA hazardous waste number (RCRA) information was added.
Section 8:          Eye/face protection information was added.
Section 8:          Respiratory protection-recommended respirators information  
                    was added
Section 8:          Eye/face protection text was added.
Section 8:          Respiratory protection-recommended respirators were added.
Section 8:          Respiratory protection-recommended respirators guide was    
                    added.
Section 8:          Respiratory protection-recommended respirators punctuation  
                    was added.
Section 8:          Eye/face protection information-punctuation-was added.
Section 14:         Transportation phrase was added.
Section 2:          Ingredient table was added.
Section 8:          Exposure guidelines ingredient information was added.
Section 8:          Exposure guidelines legend was added.
Section 8:          Exposure guidelines data source legend was added.
Section 3:          Carcinogenicity table was added.


DISCLAIMER:     The information in this Material Safety Data Sheet (MSDS) is
believed to be correct as of the date issued. 3M MAKES NO WARRANTIES,
EXPORESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR
USAGE OF TRADE. User is responsible for determining whether the 3M product is
fit for a particular purpose and suitable for user's method of use or
application. Given the variety of factors that can affect the use and
application of a 3 M product, some of which are uniquely within the user's
knowledge and control, it is essential that the user evaluate the 3M product to
determine whether it is fit for a particular purpose and suitable for user's
method of use or application.

3M provides information in electronic form as a service to its customers. Due
to the remote possibility that electronic transfer may have resulted in errors,
omissions or alteration in this information, 3M makes no representations as to
its completeness or accuracy. In addition, information obtained from a database
may not be as current as the information in the MSDS available directly from
3M.

3M MSDSs are available at www.3M.com

The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance.

© 2010 Imperial Supplies LLC Questions or comments? Contact us.