Start an Order |
|
|
|
| Start an Order |
|||
| Home > Products > Chemicals & Paint > MSDS Sheets > MSDS 71429 -- [Back] | |||
|
MSDS 71429 71429: Grd.Whl.4/1/2"Hubbed Steel [1]MSDS Last updated: 12/19/2006
MATERIAL SAFETY DATA SHEET
Used to comply with OSHA's Hazard
Communication Standard, 29 CFR 1910.1200
SECTION 1 - NAME AND PRODUCT
--------------------------------------------------------------------------------
Flexovit U.S.A. Inc.
1305 Eden-Evans Center Road
Angola, NY 14006
Phone: (716) 549-5100
Fax: (716) 549-7932
Updated: 4-1-06
Product: All Type 27, 28, 29, and Type 1 wheels including
Flexon, Flexcel, and Proflex products.
NFPA HAZARD RATING CODE
Flammability Rating
0
Health Rating
1
Reactivity Rating
0
Hazard Rating
0
SECTION II - COMPOSITION
--------------------------------------------------------------------------------
% By OSHA OSHA ACGIH Other Carcinogen
Ingredient Weight Regulate Cas # PEL TLV Limits
Aluminum 60-80 N/A 1344-28-1 NA 10mg/m N/A No
Oxide
Silicon Carbide NA N/A 409-21-2 NA NA N/A No
Zirconium 0-12 N/A 1314-23-4 NA 10mg/m N/A No
Oxide
Calcium NA N/A N/A NA 5mg/m N/A No
Hydroxide
Barium NA N/A N/A 0.5mg/m 10mg/m N/A No
Sulfate
Iron Sulfide NA N/A 1317-37-9 NA NA N/A No
Florides NA N/A 16984-48-8 2.5mg/m 2.5mg/m N/A No
Phenolic Resin 0-15 N/A 9003-35-4 5 P.P.M. 5 P.P.M. N/A No
Fiber Glass 0-5 N/A N/A 15mg/m 10mg/m N/A No
Aluminum 0.1-1 N/A N/A NA NA N/A No
Or Steel
Zinc NA N/A N/A NA NA N/A No
SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS
--------------------------------------------------------------------------------
Boiling Point N/A Specific Gravity (H2O=1) 2-4
Vapor Pressure (mm Hg.) N/A Melting Point
N/A
Vapor Density (AIR=1) N/A Evaporation rate (Butyl Acetate=1) N/A
Solubility in Water Slight Appearance/Odor Dark colored solid.
May give off some odor in use.
SECTION IV - FIRE AND EXPLOSION DATA
--------------------------------------------------------------------------------
Means of Extinction Water or carbon dioxide. Lower and Upper Explosion limits
N/A
Flammable Limits N/A Special Fire Fighting Procedures
None
Flash Point N/A Unusual Fire or Explosion Hazards
None
SECTION V - REACTIVITY DATA
--------------------------------------------------------------------------------
Stable - Avoid excessive moisture, high relative humidity, temperature extremes
and contact with acids or solvents.
Not incompatible with any materials.
Hazardous Polymerization will not occur.
Dust and organic fumes are generated in use. Do not exceed TLV's.
SECTION VI - HEALTH HAZARD DATA
--------------------------------------------------------------------------------
Route(s)of Entry Signs and symptoms of Exposure Emergency and First-Aid
procedures.
X May cause coughing and shortness Terminate exposure and
Dust inhalation. of breath during grinding. remove to fresh air.
May affect breathing capacity. Obtain medial assistance.
Ingestion No known adverse effects, but not Obtain medical assistance.
recommended.
Absorption Not absorbed through skin. N/A
Skin Contact Grinding wheel may cause Terminate exposure and remove to
abrasions. Dust may cause fresh air. Obtain medical
skin irritation. assistance.
Eye Dust or fumes may cause eye Fresh air and medical assistance.
irritation.
Other Excessive noise levels may exist Cease use. Obtain medical
in use. assistance.
Medical conditions such as emphysema and asthma may be aggravated during
grinding.
SECTION VII - STORAGE HANDLING AND USE PROCEDURES
--------------------------------------------------------------------------------
Handling and storage procedures - Avoid damage to wheel. Do not drop.
Do not use a wheel that has been damaged or dropped.
Avoid excessive temperatures in storage. Always handle in accordance with ANSI
B7.1.
Normal clean up procedures should be used if material is released.
Dispose of waste in a sanitary landfill in accordance with state, local and
federal regulations.
Always use in accordance with ANSI Z43.1 and OSHA 1910.215. Do not use dropped
or damaged wheels. Do not use without machine guard in place. Do not exceed
maximum RPM on wheel.
SECTION VIII - CONTROL MEASURES
--------------------------------------------------------------------------------
Protection Requirements and Referrals.
Respiratory OSHA or NIOSH approved respirator if TLV's exceeded.
See OSHA 29 CFR 1910.134
Ventilation Local and mechanical exhaust recommended.
See ANSI Z43.1. Refer to OSHA 29 CFR 1910.94.
Protective Gloves Not required but use if desired.
Eye Protection Required. Refer to OSHA 29 CFR 1910.133.
Hearing Protection Required. Refer to OSHA 29 CFR 1910.95.
Other Apron and/or face shield if desired.
Hygienic Practices Wash with soap and water after handling and grinding.
COMPANY USE
The information and recommendations set forth herein are taken from sources and
references believed to be accurate and complete as of the date hereof. However,
FlexOvit® U.S.A. Inc. makes no expressed or implied warranty with respect to the
accuracy of the information or the suitability of the recommendations, and
assumes no liability to any user thereof.
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance. For more product information by email, click here Imperial Supplies LLC does not provide services and products outside the United States |
Printer-Friendly View
