Start an Order |
|
|
|
| Start an Order |
|||
| Home > Products > Chemicals & Paint > MSDS Sheets > MSDS 71313 -- [Back] | |||
|
MSDS 71313 71313: Depress Cntr Grd Whl 4X1/4X5/8 [5]MSDS Last updated: 06/30/2010
MATERIAL SAFETY DATA SHEET
MSDS - 73491 - 71313 - 71429
Used to comply with OSHA's Hazard Communication Standard, 29 CFR 1910.1200
NFPA HAZARD RATING
Flammability 0
Reactivity 0
Health 1
Hazard 0
SECTION I - NAME AND PRODUCT
FLEXOVIT USA, INC. Ph: (716) 549-5100
1305 Eden Evans Center Rd, Angola, NY Fax: (716) 549-5455
14006
Product: Resinoid Bonded abrasive Updated: 05/01/09
Wheels
Contact: Technical Director
SECTION II - COMPOSITION
Ingredient % By OSHA C.A.S. # OSHA PEL ACGIH TLV Other Carcinoge
Weight Regulat Limit n
e s
Aluminum Oxide 0-80 No 1344-28- 15mg/m3 10mg/m3 N/A No
1
Silicon Carbide 0-80 No 409-21-2 15mg/m3 10mg/m3 N/A No
Zirconium Oxide 0-50 No 1314-23- 5mg/m3 10mg/m3 N/A No
4
Barium Compound 0-8 No 7727-43- 5mg/m3 10mg/m3 N/A No
7
Iron Sulfide 0-15 No 1317-37- 15mg/m3 10mg/m3 N/A No
9
Fluorides 0-15 No NA 2.5mg/m3 2.5mg/m3 N/A No
Cured Phenolic 10-30 No 9003-35- None None N/A No
Resin 4 Estab. Estab.
Carbon Black 0-.2 No 1333-86- 3.5mg/m3 3.5mg/m3 N/A No
4
Lime 0-3 No 1305-62- 5mg/m3 5mg/m3 N/A No
0
Fiberglass 0-10 No 65997-17 15mg/m3 10mg/m3 N/A No
-3
Cured Epoxy 0-5 No 68609-97 None None N/A No
Resin -2 Estab. Estab.
SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS
Physical State Solid
Vapor Pressure (mm Hg) N/A
Vapor Density (Air =1) N/A
Solubility in Water N/A
Odor/Appearance Odorless/Dark colored solid
Boiling Point N/A
Freezing Point N/A
Melting Point N/A
% Volatile N/A
Specific Gravity (H2O=1) 2-4
Odor Threshold N/A
pH N/A
Evaporation Rate N/A
Coefficient of Water/Oil Distribution N/A
SECTION IV - FIRE AND EXPLOSION DATA
Means of Extinction Water or Carbon Dioxide
Flammable Limits N/A
Flash Point N/A
Lower and Upper Explosion Limits N/A
Special Fire Fighting Procedures N/A
Unusual Fire or Explosion Hazards N/A
SECTION V - REACTIVITY DATA
Stable - Avoid excessive moisture, high relative humidity, temperature
extremes and contact with acids or solvents.
Not incompatible with any materials.
Hazardous Polymerization will not occur.
Dust and organic fumes are generated in use. Do not exceed TLV's.
SECTION VI - HEALTH HAZARD DATA
Route(s) of Entry Signs and Symptoms of Exposure Emergency and First-Aid
Procedures
Dust Inhalation May cause coughing and shortness Terminate exposure and
of breathe during grinding. May remove to fresh air.
affect breathing capacity. Obtain medical
assistance.
Ingestion No known adverse effects, but not Obtain medical
recommended. assistance.
Absorption Not absorbed through skin. N/A
Skin contact Grinding wheel may cause Terminate exposure and
abrasions. Dust may cause skin remove to fresh air.
irritation. Obtain medical
assistance.
Eye Dust or fumes may cause eye Fresh air and medical
irritation. assistance.
Other Excessive noise levels may exist Cease use. Obtain medical
in use. assistance.
Medical conditions such as emphysema and asthma may be aggravated during
grinding.
SECTION VII - STORAGE HANDLING AND USE PROCEDURES
Handling and storage procedures - Avoid damage to wheel. Do not drop. Do not
use a wheel that has been damaged.
Normal clean up procedures should be used if materials are released.
Dispose of waste in a sanitary landfill in accordance with state, local and
federal regulations.
Always use in accordance with OSHA 1910.215. Do not use dropped or damaged
wheels. Do not use without machine guard in place. Do not exceed maximum RPM
on wheel.
SECTION VIII - CONTROL MEASURES
Protection Requirements and Referrals
Respiratory OSHA or NIOSH approved respirator if TLV's exceeded.
Ventilation Local and mechanical exhaust recommended. Refer to OSHA
29 CFR 1910.94.
Protective Gloves Not required but use if desired.
Eye Protection Required. Refer to OSHA 29 CFR 1910.133
Hearing Protection Required. Refer to OSHA 29 CFR 1910.95
Other Apron and/or face shield if desired
Hygienic Practices Wash with soap and water after handling and grinding.
SECTION IX - MSDS PREPARATION
The information and recommendations set forth herein are taken from sources
and references believed to be accurate and complete as of the date hereof.
However, FLEXOVIT USA, Inc. makes no expressed or implied warranty with
respect to the accuracy of the information or the suitability of the
recommendations, and assumes no liability to any user thereof.
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance. For more product information by email, click here Imperial Supplies LLC does not provide services and products outside the United States |
