MSDS 9547

                            MATERIAL SAFETY DATA SHEET


NOTE; BLANK SPACES ARE NOT PERMITTED. IF ANY ITEM IS NOT APPLICABLE, THE SPACE
MUST BE MARKED TO INDICATE THAT.

IDENTITY
(As shown on Label or package) VLP 1oz. Only  (F-836)

Imperial Part # 9547

PART NO. IF APPLICABLE

                                    SECTION 1


MANUFACTURER'S NAME - Plasti Dip International Inc.

EMERGENCY PHONE No.  1-800-424-9300

ADDRESS  (NUMBER, STREET, CITY, STATE AND ZIP CODE)
3920 Pheasant Ridge Drive
Blaine, MN 55449

REVISION #  0001

MANUFACTURER'S PHONE No. FOR INFORMATION   1-763-785-2156

DATE MSDS WAS PREPARED  March 18, 2002


                 SECTION II - HAZARDOUS INGREDIENTS INFORMATION;


All Health Hazards which comprise 1% or greater of the composition and all
carcinogens if 0.1% of the composition or greater.

HAZARDOUS COMPONENTS
CHEMICAL and IDENTITY  %Wt     CAS NO.     OSHA       ACGIH          OTHER LIMIT
AND COMMON NAME(S      (Optional)          PEL        TLV            RECO
--------------------------------------------------------------------------------
Tetrahydrofuran        35.6    109-99-9    200 ppm    200 ppm        None
Methyl Ethyl Ketone    29.2    78-93-3     200 ppm    200 ppm        None
Cyclohexanone          2.7     108-94-1    50 ppm     25 ppm         None
Resins                 23.6    N/A         N/A        N/A            None


                SECTION III -  PHYSICAL / CHEMICAL CHARACTERISTICS


BOILING POINT        Specific Gravity (H2O=1)  Approximate Weight Per Gallon(LBS
151 - 175ºF                   0.94                            7.89

VAPOR PRESSURE          VAPOR DENSITY                    EVAPORATION RATE
143 mm Hg @ 20ºC        (AIR=1) Heavier than air         (BUTYL ACETATE=1) >1.0

SOLUBILITY IN WATER     % VOLATILE 67.4             OTHER
Insoluble                  VOC LBS./GAL  5.3          (IF ANY)

APPEARANCE
AND ODOR   Clear liquid, strong solvent odor.

SECTION IV -  FIRE AND EXPLOSION HAZARD DATA

FLASH POINT        6.0ºF         FLAMMABLE LIMITS        LEL         UEL
(METHOD USED)  TCC                 1.3 - 11.8            1.3         11.8

EXTINGUISHING
MEDIA    Carbon Dioxide, Dry Chemical, or Foam

SPECIAL FIRE FIGHTING
PROCEDURES   Self contained breathing apparatus with a full face piece, operated
in pressure demand or other positive pressure mode.

UNUSUAL FIRE AND
EXPLOSION HAZARDS  This material is flammable and may be ignited by heat,
sparks, flame or static electricity.

HAZARDOUS PRODUCTS FORMED BY
FIRE OR THERMAL DECOMPOSITION    Carbon dioxide and/or carbon monoxide. Hydrogen
                                           chloride and organic hydrocarbons.

EXPLOSIVE LIMITS
(% BY VOLUME IN AIR)   1.3 - 11.8


               SECTION V -  OPTIONAL HAZARD RATINGS IDENTIFICATION


HAZARD RATING                     National Fire Protection Association (NFPA)
4-   EXTREME
3-   HIGH                         FIRE   3      REACTIVITY  0
2-   MODERATE
1-   SLIGHT                       HEALTH  2   SPECIAL HAZARDS  None
0-   INSIGNIFICANT
**  SEE SECTION IV


                   SECTION VI -  REACTIVITY AND STABILITY DATA


STABILITY      UNSTABLE      STABLE  X
INCOMPATIBILITY (Materials to Avoid) Strong acids, bases, oxidizing agents,
selected amines with alkali metals and halogens.
HAZARDOUS DECOMPOSITION OR BY PRODUCTS
HAZARDOUS         MAY OCCUR         CONDITIONS TO AVOID
POLYMERIZATION      WILL NOT OCCUR  X      May be ignited by heat, sparks,
                        flame or static electricity.


                        SECTION VII -  HEALTH HAZARD DATA


ROUTES OF ENTRY      INHALATION? YES      SKIN?  YES
                      INGESTION:  YES      EYES?  YES
HEALTH   ACUTE       X
HAZARDS   CHRONIC  X
CARCINOGENICITY;  No

SIGNS AND
SYMPTOMS OF
EXPOSURE      Headache, Dizziness, Drowsiness, Fatigue, Irregular Heartbeat,
         Skin and Eye Irritation.

MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE
EMERGENCY AND   Ingestion:  Contact Physician or Poison Control Immediately.
FIRST AID      Inhalation: Remove to fresh air. Administer Oxygen or Artificial
PROCEDURES             Respiration if Necessary.
         Eye Contact: Flush with large amount of water. If irritation persists,
                    contact Physician.
         Skin: Wash with soap and water.


               SECTION VIII - PRECAUTIONS FOR SAFE HANDLING AND USE


STEPS TO BE TAKEN IN      Wipe up with floor absorbent. Transfer to hood.
CASE MATERIAL IS RELEASED    Prevent run-off to sewers.
OR SPILLED            Eliminate all sources of ignition. Ventilate to maintain
               exposure below P.E.L.'s . Use sand or other material
               to dam or contain spills. If large spill, notify appropriate
               state and local agencies.

WASTE DISPOSAL METHODS              Dispose of product in accordance with local,
county, state
                           and federal regulations.

PRECAUTIONS TO BE TAKEN   Avoid eye contact with eyes. Keep container closed. Us
IN HANDLING AND STORAGE   with adequate ventilation. Keep away from sparks, flam
               and heat sources   and store in a cool area. Avoid inhalation
               of vapors and personal contact with liquid product.  Use
               good personal hygiene practices.
OTHER PRECAUTIONS      Keep container closed when not in use. Containers should
               be disposed of in an environmentally safe manner in
               accordance with Governmental Regulations.


                          SECTION IX -  CONTROL MEASURES


RESPIRATORY PROTECTION (SPECIFY TYPE)  Depending on the airborne concentration,
use a
               Respirator or gas mask with appropriate NIOSH approved
               Cartridge and connister, or supplied air equipment.
PROTECTIVE GLOVES  Impervious
VENTILATION   LOCAL EXHAUST   Supplemental (if needed)      SPECIAL    None
         MECHANICAL (GENERAL)  To maintain exposure below P.E.L.'s
         OTHER      None

EYE PROTECTION             OTHER PROTECTIVE CLOTHING OR EQUIPMENT
Chemical splash goggles or         Impervious clothing/boots as needed
approved eye protection
WORK HYGIENIC PRACTICES   Wash thoroughly after handling


                     SECTION X -  TRANSPORTATION INFORMATION


D.O.T. PROPER SHIPPING NAME   Coating Solutions
D.O.T. HAZARD CLASS  3,PG II
IF A "CONSUMER COMMODITY ORM-D", WHAT IS THE HAZARD CLASS   3, PG II
D.O.T.I.D. No (N/U OR N/A)  UN1139
IATA PROPER SHIPPING NAME  Coating Solution
IATA HAZARD CLASS  3, PG II
IMO No.  None


                     SECTION XI -  313 SUPPLIER NOTIFICATION


THIS PRODUCT CONTAINS THE FOLLOWING CHEMICALS SUBJECT TO REPORTING REQUIREMENTS
OF SECTION 313 OF THE EMERGENCY PLANNING AND COMMUNITY RIGHT-TO-KNOW ACT OF
1986, 40 CFR 372, (see table on page 1 for CAS # and percent by weight). Methyl
Ethyl Ketone

WARNING; THIS PRODUCT CONTAINS A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO
CAUSE CANCER AND BIRTH DEFECTS,  OR OTHER REPRODUCTIVE HARM.

Prepared By:
Approved By:

The information provided herein is based on data considered accurate. No
warranty is expressed or implied regarding the accuracy of the data or the
results obtained from its use. Since the information contained herein may be
applied under conditions beyond the vendors control. And since subsequent data
may suggest modification of the information. Vendor assumes no responsibility
for the results of its use.

The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance.

© 2008 Imperial Supplies LLC Questions or comments? Contact us.