![]() |
![]() |
![]() |
|
| Home > Products > Chemicals & Paint > MSDS Sheets > MSDS 9108 -- [Back] | |||
|
MSDS 9108 9108: Threadlocker Blue-Gel 5 Grams [1]MSDS Last updated: 12/03/2008
Permatex, Inc.
10 Columbus Blvd.
Hartford, CT 06106 USA
Telephone: 1-87-Permatex
(877) 376-2839
Emergency: 800-255-3924
International Emergency: +01-813-248-0585
Material Safety Data Sheet
1. PRODUCT IDENTIFICATION
Product Name: MEDIUM STRENGTH THREADLOCKER BLUE GEL 5 GR
Item No: 24005
Product Type: Anaerobic
2. COMPOSITION/INFORMATION ON INGREDIENTS
Component Weight% ACGIH; TLV-TWA OSHA PEL:
POLYGLYCOL DIMETHACRYLATE 30-50 Not Listed Not Listed
25852-47-5
POLYESTER RESIN 20-40 Not Listed Not Listed
MIXTURE
BENZOATE ESTERS 10-30 Not Listed Not Listed
MIXTURE
TREATED SILICON DIOXIDE, <10 10 mg/m3 10 mg/m3
SYNTHETIC, CRYSTALLINE-FREE total dust
67762-90-7
DIMETHYLBENZYL <3 Not Listed Not Listed
HYDROPEROXIDE
80-15-9
PROPYLENE GLYCOL <3 Not Listed Not Listed
57-55-6
TITANIUM DIOXIDE 0.1-1.0 10 mg/m3 15 mg/m3 TWA
13463-67-7 (total dust)
3. HAZARDS IDENTIFICATION
Toxicity: May cause eye and skin irritation. At elevated temperatures
may cause irritation of the respiratory tract.
Irritates mucous membranes. Ingestion may irritate digestive
tract and cause nausea, vomiting and diarrhea. High
concentrations may cause central nervous system (CNS)
depression. May cause skin sensitization. Note: This product
does not contain microcyrstalline silica.
Primary Routes of Entry: Eye and skin contact, ingestion, inhalation
Signs and Symptoms of Exposure: Repeated skin contact may cause allergic skin
reactions. Skin redness. Ingestion may cause nausea and
vomiting. Inhalation overexposure may cause irritation,
coughing and flu-like symptoms. May cause pain, redness or
swelling of the eyes and excessive blinking and tear
production.
Component Weight% NTP ACGIH IARC
Carcinogens
TITANIUM DIOXIDE 0.1-1.0 male rat-negative, A4 Group 2B; Vol
13463-67-7 female rat-negative 93,2006:
male mice-negative, Vol 47,1989
female mice-negative
Medical Conditions Recognized as Preexisitng skin disorders
Being Aggravated by Exposure:
4. FIRST AID MEASURES
Ingestion: If swallowed, DO NOT induce vomiting. Keep individual calm.
Obtain medical attention.
Inhalation: Move to fresh air in case of accidental inhalation of vapours.
Obtain medical attention.
Skin Contact: Wash off with soap and water. If skin irritation persists,
call a physician.
Eye Contact: In case of contact, immediately flush eyes with plenty of water
for at least 15 minutes and get medical attention if
irritation persists.
5. FIRE FIGHTING MEASURES
Flash Point °F(C°): >200 degrees F
Recommended Extinguishing Media: Water fog, carbon dioxide, foam, dry
chemical.
Specail Fire-Fighting Procedures: Firefighters should wear self-contained
breathing apparatus.
Hazardous Products of Combustion: Irritating vapors
Unusual Fire/Explosion Hazards: Closed containers may rupture or explode when
exposed to extreme heat.
Lower Explosive Limit: Not determined
Upper Explosive Limit: Not determined
6. ACCIDENTAL RELEASE MEASURES
Spill Procedures: Maintain good ventilation. Take up with an inert absorbent.
Store in a closed waste container until disposal.
7. HANDLING AND STORAGE
Storage: Store below 100 degrees F.
Handling: Avoid prolonged skin contact. Keep away from eyes.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Eyes; Safety glasses.
Skin: Neoprene or nitrile gloves recommended.
Ventilation: General; local exhaust ventilation as necessary to control
any air contaminants to within their exposure
limits (or to the lowest feasible levels when limits have
not been established) during the use of this product.
Respiratory Protection: An approved organic vapor respirator should be worn
when exposures are expected to exceed the applicable limits.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Blue gel
Odor: MILD
Boiling Point: >150°C
pH: Does not apply
Solubility in Water: Insoluble
Specific Gravity: 1.1
VOC Content(Wt.%): <2% by weight
Vapor Pressure: Not determined
Vapor Density (Air=1): Heavier than air
Evaporation Rate: Not determined
10. STABILITY AND REACTIVITY
Chemical Stability: Stable at normal conditions
Hazardous Polymerization: WILL NOT OCCUR.
Incompatabilities: Strong oxidizers, free radical initiators, inert
gases
Conditions to Avoid: Heat
Hazardous Products of Combustion: Irritating vapors
11. TOXICOLOGICAL INFORMATION
See Section 3
12. ECOLOGICAL INFORMATION
No data available
13. DISPOSAL CONSIDERATIONS
Recommended Method of Disposal: Disposal should be made in accordance with
federal, state and local regulations.
US EPA Waste Number: NH - Not a RCRA Hazardous Waste Material
14. TRANSPORTATION INFORMATION
DOT (49CFR 172)
Domestic Ground Transport
DOT Shipping Name: Unrestricted
Hazard Class: None
UN/ID Number: None
IATA
Proper Shipping Name: Not regulated
Class or Division: None
UN/ID Number: None
IMDG
Proper Shipping: Unrestricted
Hazard Class: None
UN Number: None
Marine Pollutant: None
15. REGULATORY INFORMATION
SARA 313 Chemicals: The following component(s) is listed as a SARA Section 313
Toxic Chemical.
DIMETHYLBENZYL HYDROPEROXIDE
CALIFORNIA PROP 65:
No California Prop 65 chemicals are known to be present at or above the No
Significant Risk Level.
TSCA Inventory Status:
Listed on Inventory: YES All components of this product are listed (or exempt)
on the EPA TSCA inventory.
16. OTHER INFORMATION
Estimated NFPA Rating: HEALTH 2, FLAMMABILITY 1 , REACTIVITY 1.
Estimated HMIS Classification: HEALTH 2, FLAMMABILITY 1, PHYSICAL HAZARD 0
NFPA is a registered trademark of the National Fire Protection Assn.
HMIS is a registered trademark of the National Paint and Coatings Assn.
Prepared By: Denise Boyd, Manager-Environmental, Health & Safety
Revision Date: July/26/2007
Company: Permatex. Inc. 10 Columbus Blvd. Hartford, CT USA 06106
Revision 1
Number:
Telephone No: 1-87-Permatex (877) 376-2839
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance. For more product information by email, click here Imperial Supplies LLC does not provide services and products outside the United States |