Start an Order |
|
|
|
| Start an Order |
|||
| Home > Products > Chemicals & Paint > MSDS Sheets > MSDS 9103 -- [Back] | |||
|
MSDS 9103 9103: Threadlocker Hvy Dty Red 6ML [2]MSDS Last updated: 12/23/2009
IMPERIAL SUPPLIES LLC MSDS SHEET FOR 9103
Permatex, Inc.
10 Columbus Blvd.
Hartford, CT 06106 USA
Telephone: 1-87-Permatex
(877) 376-2839
Emergency: 800-255-3924
International Emergency: 813-248-0585
Material Safety Data Sheet
1. PRODUCT IDENTIFICATION
Product Name: HIGH STRENGTH THREADLOCKER RED 6ML
Item No: 27100
Product Type: Anaerobic
2. COMPOSITION/INFORMATION ON INGREDIENTS
Component Weight% ACGIH TLV: TWA OSHA PEL:
POLYGLYCOL DIMETHACRYLATE 60-80 Not Listed Not Listed
25852-47-5
POLYESTER RESIN MIXTURE 20-40 Not Listed Not Listed
DIMETHYLBENZYL <3 Not Listed Not Listed
HYDROPEROXIDE
80-15-9
SACCHARIN 0.5-2.0 10mg/m3 nuisance Not Listed
81-07-2 dust
3. HAZARDS IDENTIFICATION
Toxicity: At elevated temperatures may cause irritation of the
respiratory tract. Irritates mucous membranes.
Ingestion may irritate digestive tract and cause nausea,
vomiting and diarrhea. High concentrations may cause
central nervous system (CNS) depression. May cause eye
and skin irritation. May cause skin sensitization. Note:
This product does not contain microcyrstalline silica.
Primary Routes of Eye and skin contact, ingestion, inhalation
Entry:
Signs and Symptoms of Repeated skin contact may cause allergic skin reactions.
Exposure: Skin redness. Ingestion may cause nausea and vomiting.
Inhalation overexposure may cause irritation, coughing
and flu-like symptoms. May cause pain, redness or
swelling of the eyes and excessive blinking and tear
production.
Component Weight% NTP ACGIH Carcinogens IARC
SACCHARIN 0.5-2.0 Delisted April 2000 Group 3: Vol
81-07-2 73, Page 517:
1999
Medical Conditions Recognized as Preexisting skin disorders.
Being Aggravated by Exposure:
4. FIRST AID MEASURES
Ingestion: If swallowed, DO NOT induce vomiting. Keep individual calm.
Obtain medical attention.
Inhalation: Move to fresh air in case of accidental inhalation of vapours.
Obtain medical attention.
Skin Wash off with soap and water. If skin irritation persists, call a
Contact: physician.
Eye Contact: In case of contact, immediately flush eyes with plenty of water
for at least 15 minutes and get medical attention if irritation
persists.
5. FIRE FIGHTING MEASURES
Flash Point (°F/C): >200°C
Recommended Extinguishing Dry chemical, Carbon dioxide, foam.
Media:
Special Fire-Fighting Firefighters should wear self-contained
Procedures: breathing apparatus. Water spray may be
ineffective on flames but should be used to
keep fire-exposed containers cool.
Hazardous Products of Oxides of carbon
Combustion:
Unusual Fire/Explosion Closed containers may rupture or explode when
Hazards: exposed to extreme heat. May polymerize
exothermically.
Lower Explosive Limit: Not determined
Upper Explosive Limit: Not determined
6. ACCIDENTAL RELEASE MEASURES
Spill Procedures: Maintain good ventilation. Take up with an inert absorbent.
Store in a closed waste container until disposal.
7. HANDLING AND STORAGE
Storage: Store away from heat. Store away from water or moisture. Protect
from contamination. Keep containers tightly closed in a cool,
well-ventilated place.
Handling: Avoid prolonged skin contact. Keep away from eyes.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Eyes: Safety glasses
Skin: Rubber or plastic gloves.
Ventilation: General; local exhaust ventilation as necessary to control
any air contaminants to within their exposure limits (or
to the lowest feasible levels when limits have not been
established) during the use of this product.
Respiratory An approved respirator (i.e. NIOSH, etc.) should be worn
Protection: when exposures are expected to exceed the applicable
limits.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Red liquid
Odor: MILD
Boiling Point: >150°C
pH: Does not apply
Solubility in Water: Insoluble
Specific Gravity: 1.1
VOC Content(Wt.%): <2% by weight
Vapor Pressure: Not determined
Vapor Density (Air=1): Heavier than air
Evaporation Rate: Not Determined
10. STABILITY AND REACTIVITY
Chemical Stability: Stable at normal conditions
Hazardous Polymerization: Will not cccur
Incompatabilities: Strong oxidizers, free radical initiators, inert
gases, Peroxides, Reducing agents, Oxygen
scavengers
Conditions to Avoid: Heat
Hazardous Products of Oxides of carbon
Combustion:
11. TOXICOLOGICAL INFORMATION
See Section 3
12. ECOLOGICAL INFORMATION
No data available
13. DISPOSAL CONSIDERATIONS
Recommended Method of Disposal should be made in accordance with
Disposal: federal, state and local regulations.
US EPA Waste Number: NH - Not a RCRA Hazardous Waste Material
14. TRANSPORTATION INFORMATION
DOT (49CFR 172)
Domestic Ground Transport
DOT Shipping Name: Unrestricted
Hazard Class: None
UN/ID Number: None
Marine Pollutant: None
IATA
Proper Shipping Name: Not regulated
Class or Division: None
UN/NA Number: None
IMDG
Proper Shipping: Unrestricted
Hazard Class: None
UN Number: None
15. REGULATORY INFORMATION
SARA 313 Chemicals: The following component(s) is listed as a SARA Section 313
Toxic Chemical.
DIMETHYLBENZYL HYDROPEROXIDE
CALIFORNIA PROP 65:
No California Prop 65 chemicals are known to be present at or above the No
Significant Risk Level.
TSCA Inventory Status:
Listed on Inventory: YES All components of this product are listed (or exempt)
on the EPA TSCA inventory.
16. OTHER INFORMATION
Estimated NFPA Rating: HEALTH 2, FLAMMABILITY 1 , REACTIVITY 1
Estimated HMIS Classification: HEALTH 2, FLAMMABILITY 1, PHYSICAL HAZARD 0
NFPA is a registered trademark of the National Fire Protection Assn.
HMIS is a registered trademark of the National Paint and Coatings Assn.
Prepared By: Denise Boyd, Health and Safety Revision August/13/2007
Manager Date:
Company: Permatex. Inc. 10 Columbus Blvd. Revision 1
Hartford, CT USA 06106 Number:
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance. For more product information by email, click here Imperial Supplies LLC does not provide services and products outside the United States |
