MSDS 7567

Permatex, Inc.
10 Columbus Blvd.
Hartford, Ct 06106 USA
Telephone: 1-87-Permatex
(877) 376-2839
Emergency: 800-255-3924
International Emergency: 813-248-0585

                       MATERIAL SAFETY DATA SHEET

1. PRODUCT IDENTIFICATION
Product Name:    09101  FUEL TANK REPAIR KIT  PART 2
Item No:         PTX209800C
Product Type:    Hardener

2. COMPOSITION/INFORMATION ON INGREDIENTS
Ingredient              Weight Percent   ACGIH TLV:       OSHA PEL:
Mercaptan Polymer            >70        Not Listed       Not Listed
Mixture

Epoxy Curing Agent           <30        Not Listed       Not Listed
Mixture

3. HAZARDS IDENTIFICATION
Toxicity:  Slightly toxic by inhalation. Can cause irritation of respiratory
      tract and nausea. Overexposure may cause delayed lung injury and chemical
      pneumonia. Can cause severe skin and eye irritation or burns.
      May cause permanent visual impairment. May cause skin sensitization.
      Note: Due to this product's physical  composition, the release of
      dust is not expected to occur under normal conditions of use.
Primary Routes of Entry:  Eye and skin contact, ingestion, inhalation.
Signs and Symptoms of Exposure: See Toxicity section.

Medical Conditions Recognized as        None known.
Being Aggravated by Exposure:

4. FIRST AID MEASURES
Ingestion:  If swallowed, do NOT induce vomiting. Give victim two
            glasses of water. Call a physician immediately.
            Never give anything by mouth to an unconscious person.
Inhalation: Move to fresh air in case of accidental inhalation of vapors.
            Oxygen or artificial respiration if needed.
            Obtain medical attention.
Skin Contact: Wash off immediately with soap and plenty of water
            removing all contaminated clothes and shoes.
            If skin irritation persists, call a physician.
Eye Contact: In case of contact, immediately flush eyes with plenty of
            water for at least 15 minutes and get medical attention if
            irritation persists.

5. FIRE FIGHTING MEASURES
Flash Point (F/C):     495 F  COC
Recommended Extinguishing Media:  Water fog, carbon dioxide, foam,
            dry chemical.
Special Fire-Fighting Procedures:   Firefighters should wear self-contained
            breathing apparatus. Water spray may be ineffective on
            flames but should be used to keep fire-exposed containers
            cool.
Hazardous Products of Combustion:  Oxides of nitrogen, Hydrogen
            Sulfide, Oxides of sulfur, Oxides of carbon
Unusual Fire/Explosion Hazards:  None.

Lower Explosive Limit: Not determined.
Upper Explosive Limit: Not determined.

6. ACCIDENTAL RELEASE MEASURES
Spill Procedures:  Maintain good ventilation.  Take up with an inert
                   absorbent. Store in a closed waste container until
                   disposal. Prevent from entering waterways or sewers.

7. HANDLING AND STORAGE
Storage:    Store in a cool, dry area.
Handling:   Avoid prolonged skin contact. Keep away from eyes.

8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Eyes:       Safety glasses. An eye wash station should be readily
            available.
Skin:       Chemical resistant gloves. Clean clothing to cover skin.
Ventilation: General: local exhaust ventilation as necessary to control
            any contaminants to within their exposure limits
            (or to the lowest feasible levels when limits have not been
            established) during the use of this product.
Respiratory Protection:  An approved respirator (i.e. NIOSH, etc.) should
            be worn when exposures are expected to exceed the
            applicable limits.

9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance:            Colorless to pale yellow liquid
Odor:                  MERCAPTAN ODOR
Boiling Point:         Not determined.
pH:                    Does not apply
Solubility in Water:   Nil
Specific Gravity:      1.15
VOC Content(Wt.%):     Not Determined
Vapor Pressure:        Not Determined
Vapor Density (Air=1): Not Determined
Evaporation Rate:      Not Determined

10. STABILITY AND REACTIVITY
Chemical Stability:    Stable at normal conditions
Hazardous Polymerization:    WILL NOT OCCUR.
Incompatibilities:     Strong oxidizers, Amines
Conditions to Avoid:   High temperatures
Hazardous Products of Combustion:  Oxides of nitrogen, Hydrogen
                 Sulfide, Oxides of sulfur, Oxides of carbon.

11. TOXICOLOGICAL INFORMATION
See Section 3

12. ECOLOGICAL INFORMATION
No data available

13. DISPOSAL CONSIDERATIONS
Recommended Method of Disposal:  Disposal should be made in accordance with
federal, state and local regulations.
US EPA Waste Number:     NH - Not a RCRA Hazardous Waste Material

14. TRANSPORTATION INFORMATION
DOT  (49CFR 172)

Domestic Ground Transport
      DOT Shipping Name:     Unrestricted
      Hazard Class:          None
      UN/ID Number:          None
      Marine Pollutant:      None

IATA
      Proper Shipping Name:  Not regulated
      Class or Division:     None
      UN/NA Number:          None

IMDG
      Proper Shipping:       Unrestricted
      Hazard Class:          None
      UN Number:             None

15. REGULATORY INFORMATION
SARA 313 Chemicals: The following component(s) is listed as a SARA Section 313
Toxic Chemical.

NONE

CALIFORNIA PROP 65:
No California Prop 65 chemicals are known to be present.

TSCA Inventory Status:
Listed on Inventory:  YES All components of this product are listed (or exempt)
on the EPA TSCA inventory.

16.  OTHER INFORMATION
Estimated NFPA Rating:         Health 2, Flammability 1, Reactivity 1
Estimated HMIS Classification: Health 2, Flammability 1,
                               Physical Hazard 0
NFPA is a registered trademark of the National Fire Protection Assn.
HMIS is a registered trademark of the National Paint and Coatings Assn.

Prepared By:  Denise Boyd, Health and Safety Manager    Revision Date:
                                                        January/10/2007
Company:      Permatex Inc. 10 Columbus Blvd. Hartford, CT USA 06106
                                                        Revision 3
                                                        Number:

The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance.

© 2008 Imperial Supplies LLC Questions or comments? Contact us.