![]() |
![]() |
![]() |
|
| Home > Products > Chemicals & Paint > MSDS Sheets > MSDS 7550 -- [Back] | |||
|
MSDS 7550 7550: Dielectric Grease [4]MSDS Last updated: 04/29/2008
MSDS DOCUMENT
Product Dynatex R 49634 Dielectric Grease
1. Chemical Product and Company Identification
Trade Name of this Product Dynatex R 49634 Dielectric Grease
MSDS ID DYN49634
Manufacturer Phone Number
Dynatex Inc. (270) 769-3385
350 Ring Road Emergency Phone
Elizabethtown, KY 42701 CHEMTREC (800) 424-9300
Revision Date 8/9/2005
Health 1
Fire 0
Reactivity 0
Specific
2. Composition and Information on Ingredients
Ingredient CAS Number Weight % ACGIH TLV PEL STEL
Amorphous fumed 112945-52-5 5%-15% 10 mg/m 6 mg/m
Silica
3. Hazard Identification
Primary Routes of Entry
Eye contact, skin contact.
Existing Conditions Aggravated by Exposure
No known applicable information.
4. First Aid Information
Eye Contact
Immediately flush eyes with water for at least 15 minutes. Get medical
attention if irritation develops.
Skin Contact
Wash with soap and water. If irritation occurs, seek medical attention.
Inhalation
No first aid should be needed.
Ingestion
DO NOT INDUCE VOMITING. Seek immediate medical attention.
5. FIRE FIGHTING MEASURES
Flash Point >575F
Auto-ignition Temperature
Not determined
Lower Explosive Limit
Not determined
Upper Explosive Limit
Not determined
Extinguishing Media
Use carbon dioxide or dry chemical on small fires. Use foam and/or water
spray for large fires.
Special Fire Fighting Procedures
Self-contained breathing apparatus and protective clothing should be worn
when fighting fires involving chemicals.
Unusual Fire or Explosion Hazards
None known
6. Accidental Release Measures
Steps to be taken in case of spill or release
Observe all personal protection equipment recommendations in Sections 5
and 8. Wipe or scape up and contain for salvage or disposal. Clean area as
appropriate since spilled materials, even in small quantities, may present a
slip hazard. Final cleaning may require use of steam, solvents or detergents.
Dispose of saturated absorbant or cleaning materials appropriately, since
spontaneous heating may occur. Local, state and federal laws and regulations
may apply to releases and disposal of this material, as well as those
materials and items employed in the cleanup of releases. You will neeed to
determine which federal, state and local laws and regulations are applicable.
Sections 13 and 15 of this MSDS provide information regarding certain federal
and state requirements.
7. Handling and Storage
Handling
Keep container closed when not in use. Avoid prolonged skin contact.
Keep away from eyes. use recommended personal protective equipment.
Storage
Store below 100 degrees F.
8. Exposure Controls and Personal Protection
Eye Protection
Use proper protection - safety glasses as a minimum.
Skin Protection
Chemical protective gloves are recommended. Wash at mealtimes and end of shift.
Respiratory Protection
No special requirements under ordinary conditions of use and with
adequate ventilation.
Precautionary Measures
Avoid eye and skin contact. Keep container closed when not in use.
Do not take internally.
9. Physical and Chemical Properties
Physical State Paste
Specific Gravity 1.03
Color/Appearance Translucent
Odor Slight, sweet
pH Not applicable
Boiling/Cond. Point >300C
Melting/Freezing Point Not applicable
Solubility Insoluble in water
VOC % < 1.5%
Viscosity Not applicable
Vapor Density > 1
Vapor Pressure < 5 mm Hg @ 25C
Note
The above information is not intended for use in preparing product
specifications. Contact Accumetric LLC before writing specifications.
10. Stability and Reactivity
Chemical Stability
Stable
Materials to Avoid / Incompatibilities
Strong acids, bases and strong oxidizers.
Conditions to Avoid
None known
Hazardous Polymerization
Will not occur
11. Toxicological Information
Carcinogenicity
This product is not known to be a carcinogen.
Mutagenicity
This product is not known to be a mutagen.
Reproductive Toxin
This product is not known to be a reproductive toxin.
Sensitizer
This product is not known to be a sensitizer.
Teratogenicity
This product is not known to be a teratogen.
12. Ecological Information
Environmental Fate and Distribution
Complete information is not yet available.
Environmental Effects
Complete information is not yet available.
Fate and Effects in Waste Water Treatment Plants
Complete information is not yet available.
13. Disposal Considerations
Waste Disposal Method
We make no guarantee or warranty of any kind that the use or disposal of
this product complies with all local, state, or federal laws. It is also the
obligation of each user of the product mentioned herein to determine and
comply with the requirements of all applicable statutes.
This product is not known to be regulated under RCRA regulations. Disposal of
unused portions of this product and process waste containing this product
should be done only after a careful evaluation and in compliance with all
federal, local and state laws.
14. Transportation Information
DOT Road Shipment Information
DOT Shipping Name: Unrestricted
DOT Hazard Class: None-hazardous, unrestricted
UN/NA Number: None
Label Required: No special labeling is required
15. Regulatory Information
The contents of this MSDS comply with the OSHA Hazard Communication
Standard 29 CFR 1910.1200.
TSCA Status
All chemical substances in this material are included on or exempted from
listing on the TSCA Inventory of Chemical Substances.
SARA Title III Section 302 Extremely Hazardous Substances
None
SARA Title III Section 304 CERCLA hazardous Substances
None
SARA Title III Section 311/312
No components subject to 40 CFR 370
SARA Title III Section 313 Toxic Chemicals
None present or none present in regulated quantities.
California Proposition 65
This product contains the following chemical(s) listed by the State of
California under the Safe Drinking Water and Toxic Enforcement Act of 1986
(Proposition 65) as being known to cause cancer, birth defects or other
reproductive harm:
None known
Massachusetts
Silica, amorphous fumed (112945-52-5)
New Jersey
Silica, amorphous fumed (112945-52-5)
Pennsylvania
Silica, amorphous fumed (112945-52-5)
16. Other Information
Disclaimer
The data contained herein is based upon information that Accumetric LLC
believes to be reliable. Users of this product have the responsiblity to
determine that suitability of use and to adopt all necessary precatuions to
ensure the safety and protection of property and persons involved in said
use. All statements to suggestions are made without warranty, expressed or
implied, regarding the accuracy of the information, the hazards connected
with the use of the material or the results to be obtained from the use
therof.
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance. For more product information by email, click here Imperial Supplies LLC does not provide services and products outside the United States |