![]() |
![]() |
![]() |
|
| Home > Products > Chemicals & Paint > MSDS Sheets > MSDS 7543 -- [Back] | |||
|
MSDS 7543 7543: Threadlocker Red 6ML [2]7544: Threadlocker Red 24ML [2] MSDS Last updated: 04/30/2009
MSDS Document
Product Dynatex® 49451 Red Boltlocker - High Strength
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Trade Name of this Product - Dynatex® 49451 Red Boltlocker - High Strength
MSDS ID DYN49451
MANUFACTURER PHONE NUMBER
Dynatex Inc. (270) 769-3385
350 Ring Road EMERGENCY PHONE
Elizabethtown, KY 42701 CHEMTREC (800) 424-9300
Revision Date: 4/25/07
Fire 1
Health 1
Reactivity 1
Specific
2. COMPOSITION AND INFORMATION ON INGREDIENTS
INGREDIENT CAS # WEIGHT % ACGIH TLV PEL STEL
Saccharin 81-07-2 1%-3%
Cumene Hydroperoxide 80-15-9 1%-3% 1 ppm Skin None
Amorphous fumed silica 112945-52-5 0.1%-1% 10 mg/m3 6 mg/m3
3. HAZARD IDENTIFICATION
PRIMARY ROUTES OF ENTRY
Eye contact, skin contact.
TOXICITY
Mild eye irritant
SYMPTOMS OF OVEREXPOSURE
May cause dermatitis with prolonged contact on sensitive individuals. May
cause respiratory tract irritation
EXISTING CONDITIONS AGGRAVATED BY EXPOSURE
Eye, skin and respiratory disorders.
4. FIRST AID INFORMATION
EYE CONTACT
Flush with warm water for several minutes. Obtain medical attention.
SKIN CONTACT
Wash affected area thoroughly with soap and water. Remove contaminated clothing
and launder before re-use. Get medical attention if irritation develops.
INHALATION
Remove to fresh air. If symptoms persist, obtain appropriate medical attention.
INGESTION
Do not induce vomiting. Keep calm. Obtain medical attention.
5. FIRE FIGHTING MEASURES
Flash Point >200°F
FP Method TCC
EXTINQUISHING MEDIA
Carbon Dioxide, Dry Chemical, Foam
SPECIAL FIRE FIGHTING PROCEDURES
None
UNUSUAL FIRE OR EXPLOSION HAZARDS
None known
HAZARDOUS DECOMPOSITION PRODUCTS
Thermal breakdown of this product during fire or very high heat conditions may
evolve the following hazardous decomposition products:
Irritating organic vapors
Oxides of carbon, sulfur and nitrogen.
6. ACCIDENTAL RELEASE MEASURES
STEPS TO BE TAKEN IN CASE OF SPILL OR RELEASE
Observe all personal protection equipment recommendations. Soak up with inert
absorbent. Store in a partly filled, closed container until disposal. Prevent
product from entering drains. Local, state and federal regulations may apply to
releases and disposal of this material, as well as those materials and items
employed in cleanup of releases.
7. HANDLING AND STORAGE
HANDLING
Avoid contact with skin, eyes, and clothing. Avoid breathing vapor or mist.
STORAGE
Store at or below 100 F. Keep away from heat, sparks and open flames.
8. EXPOSURE CONTROLS AND PERSONAL PROTECTION
EYE PROTECTION
Safety goggles or glasses with side shields are recommended.
SKIN PROTECTION
Rubber, polyethylene, or neoprene gloves.
VENTILATION
Local exhaust ventilation is recommended to maintain vapor level below TLV.
RESPIRATORY PROTECTION
Use NIOSH approved respirator for individuals who are sensitive.
9. PHYSICAL AND CHEMICAL PROPERTIES
Physical State Liquid
Specific Gravity 1.1
Color/Appearance Red
Odor Mild
Boiling/Cond. Point >300°F
Solubility Negligible
VOC% 135% 142 g/L
Vapor Density Approx. 3 (Air=1)
Vapor Pressure <5mm Hg @ 200°F
NOTE:
The above information is not intended for use in preparing product
specifications.
Contact Accumetric LLC before writing specifications.
10. STABILITY AND REACTIVITY
CHEMICAL STABILITY
Stable
CONDITIONS TO AVOID
None known
HAZARDOUS POLYMERIZATION
Will not occur
HAZARDOUS DECOMPOSITION PRODUCTS
Oxides of carbon, sulfur, and nitrogen
11. TOXICOLOGICAL INFORMATION
COMPONENT TOXICOLOGY INFORMATION
No known applicable information.
SPECIAL HAZARD INFORMATION ON COMPONENTS
No known applicable information.
12. ECOLOGICAL INFORMATION
ENVIRONMENTAL FATE AND DISTRIBUTION
Complete information is not yet available.
ENVIRONMENTAL EFFECTS
Complete information is not yet available.
FATE AND EFFECTS IN WASTE WATER TREATMENT PLANTS
Complete information is not yet available.
13. DISPOSAL CONSIDERATIONS
WASTE DISPOSAL METHOD
We make no guarantee or warranty of any kind that the user or disposal of this
product complies with all local, state, or federal laws. It is also the
obligation of each user of the product mentioned herein to determine and comply
with the requirements of all applicable statutes.
This product is not known to be regulated under RCRA regulations. Disposal of
unused portions of this product and process waste containing this product
should be done only after a careful evaluation and in compliance with all
federal, local and state laws.
14. TRANSPORTATION INFORMATION
DOT ROAD SHIPMENT INFORMATION
Not subject to DOT.
OCEAN SHIPMENT (IMDG)
Not subject to IMDG code.
AIR SHIPMENT (IATA)
Not subject to IATA regulations.
15. REGULATORY INFORMATION
The contents of this MSDS comply with the OSHA Hazard Communication Standard
29 CFR 1910.1200.
TSCA STATUS
All chemical substances in this material are included on or exempted from
listing on the TSCA Inventory of Chemical Substances.
SARA TITLE III SECTION 302 EXTREMELY HAZARDOUS SUBSTANCES
None
SARA TITLE III SECTION 304 CERCLA HAZARDOUS SUBSTANCES
None
SARA TITLE III SECTION 312 HAZARD CLASS
Acute: Yes
Chronic: No
Fire: No
Pressure: No
Reactive: No
SARA TITLE III SECTION 313 TOXIC CHEMICALS
Cumene Hydroperoxide (80-15-9)
CALIFORNIA PROPOSITION 65
This product contains the following chemical(s) listed by the State of
California under the Safe Drinking Water and Toxic Enforcement Act of 1986
(Proposition 65) as being known to cause cancer, birth defects or other
reproductive harm:
Saccharin. Proper usage necessitates no Proposition 65 warning.
NEW JERSEY
Cumene hydroperoside (80-15-9)
Saccharin (81-07-2)
PENNSYLVANIA
Cumene hydroperoxide (80-15-9)
Saccharin (81-07-2)
16. OTHER INFORMATION
DISCLAIMER
The data contained herein is based upon information that Accumetric LLC
believes to be reliable. Users of this product have the responsibility to
determine that suitability of use and to adopt all necessary precautions to
ensure the safety and protection of property and persons involved in said use.
All statements to suggestions are made without warranty, expressed or implied,
regarding the accuracy of the information, the hazards connected with the use
of the material or the results to be obtained from the use thereof.
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance. For more product information by email, click here Imperial Supplies LLC does not provide services and products outside the United States |