MSDS Sheet 6620

• All Products
• Fasteners
   » Grade 8
   » Grade 5
   » Threaded Fasteners
• Hardware
• Rivet & Rivet Guns
• Vehicle Lighting
   » Cross Reference
• Electrical Products
• Tubing & Tube Fittings
• Air Brake Products
• Hose & Hose Ends
• Cutting Tools
• Abrasives
• Safety Products &
  Welding Supplies
• Chemicals & Paint
   » MSDS Information
   » CA/OTC Information
• Shop Supplies
• Vehicle Parts &
  Accessories
• Assortments &
  Steel Equipment
   » Assortment Listing

• Online Catalog Index
• Discontinued &
Overstock Specials

Print Rev. Date 08/17/2006 MSDS DOCUMENT Product Dynatex ® 55016 Transmission Assembly Lube 1. Chemical Product and Company Identification Trade Name of this Product Dynatex® 55016 Transmission Assembly Lube MSDS ID DYN55016 Manufacturer Phone Number Dynatex Inc. (270) 769-3385 350 Ring Road Emergency Phone Elizabethtown, KY 42701 CHEMTREC (800) 424-9300 Revision Date 8/15/2006 Fire 1 Health: 0 Health 0 Fire: 0 Reactivity 0 Reactivity: 0 Specific Specific PPE: B 2. Composition and Information on Ingredients Ingredient CAS Number Weight % ACGIH TLV PEL STEL Distillates 64742-54-7 50%-75% 5 mg/m3 5 mg/m3 10 mg/m3 hydrotreated heavy paraffinic Petroleum distillates,64742-65-0 50%-70% 0 Solvent dewaxed heavy Paraffinic 3. Hazard Identification Primary Routes of Entry Eye contact, skin contact. Symptoms of Exposure Irritated eyes and skin Acute Overexposure Effects None recognized Chronic Overexposure Effects Prolonged or repeated skin contact may cause skin irritation. 4. First Aid Information Eye Contact Immediately flush eyes with water for at least 15 minutes. Get medical attention if irritation develops. Skin Contact Remove contaminated clothing and wash skin with soap and water. Get medical attention if irritation persists. Ingestion DO NOT INDUCE VOMITING. See immediate medical attention. Inhalation The vapor pressure is very low. Vapor inhalation under ambient conditions is normally not a problem. If overcome by vapor from hot product, immediately remove from exposure and seek medical attention. If breathing has stopped, start resuscitation: administer oxygen if breathing is irregular. If overexposed to oil, remove from further exposure until excessive mist conditions subside. 5. Fire Fighting Measures Flash Point 400F FP Method COC Lower Explosive Limit Not determined Upper Explosive Limit Not determined Extinguishing Media Carbon Dioxide, Dry Chemical, Foam, Water Spray Unusual Fire and Explosion Hazards Pressure will increase in over-heated, closed containers. Special Fire Fighting Procedures Water or foam may cause frothing. Use water to keep fire exposed containers cool. Water spray may be used to flush spills away from exposure. Minimize breathing gases, vapor, fumes or decomposition products. Use self-contained breathing apparatus for enclosed or confined spaces or as otherwise needed. 6. Accidental Release Measures Steps to be taken in case of spill or release Recover free product. Add sand, earth or other suitable absorbent to spill area. Minimize skin contact. Keep product out of sewers and watercourses by diking or impounding. Advise authorities if product has entered or may enter sewers, watercourses or extensive land areas. Assure conformity with applicable governmental regulations. Spilled material, unused contents and empty containers must be disposed of in accordance with local, state and federal regulations. 7. Handling and Storage Handling Avoid eye contact and repeated prolonged contact with the skin. Keep out of reach from children. Storage Do not store near or mix with strong oxidizers. Do not store sealed container near extreme heat. Do not reuse container. Precautionary Measures Always wash hands well before touching face or eating. 8. Exposure Controls and Personal Protection Eye Protection Use splash goggles or face shield when eye contact may occur. Skin Protection Use chemical resistant gloves, if needed, to avoid prolonged or repeated skin contact. Ventilation Good general ventilation should be sufficient. Respiratory Protection No respiratory protection should be needed. Suitable Respirator: None should be needed. Other Protective Equipment Use chemical-resistant apron or other impervious clothing, if needed, to avoid contaminating regular clothing, which could result in prolonged or repeated skin exposure. 9. Physical and Chemical Properties Specific Gravity 0.89 Color/Appearance Blue Odor Mild odor Melting/Freezing Point 140F Solubility Negligible in water (<0.1%) Evaporation Rate <0.01 (Butyl Actate = 1) Vapor Density >5 (air = 1) Vapor Pressure <0.01 mm Hg @ 20C) Note: The above information in not intended for use in preparing product specifications. Contact Accumetric LLC before writing specifications. 10. Stability and Reactivity Chemical Stability This product is stable and will not react violently with water. Hazardous Polymerization Will not occur Materials to Avoid Strong oxidants such as liquid chlorine, concentrated oxygen, sodium hypochlorite or calcium hypochlorite. Conditions to Avoid None established Hazardous Decomposition Products Carbon oxides 11. Toxicological Information Sensitizer This product is not known to be a sensitizer. Carcinogenicity This product is not known to be a carcinogen. Reproductive Toxin This product is not known to be a reproductive toxin. Teratogenicity This product is not known to be a teratogen. Mutagenicity This product is not known to be a mutagen. 12. Ecological Information Environmental Effects Complete information is not yet available. Environmental Fate and Distribution Complete information is not yet available. Fate and Effects in Waste Water Treatment Plants Complete information is not yet available. 13. Disposal Considerations Waste Disposal Method We make no guarantee or warranty of any kind that the use or disposal of this product complies with all local, state, or federal laws. It is also the obligation of each user of the product mentioned herein to determine and comply with the requirements of all applicable statues. This product is not known to be regulated under RCRA regulations. Disposal of unused portions of this product and process waste containing this product should be done only after a careful evaluation and in compliance with all federal, local and state laws. 14. Transportation Information 15. Regulatory Information The contents of this MSDS comply with the OSHA Hazard Communication Standard 29 CFR 1910.1200. TSCA Status All chemical substances in this material are included on or exempted from listing on the TSCA Inventory of Chemical Substances. SARA Title III Section 302 Extremely Hazardous Substances None SARA Title III Section 304 CERCLA Hazardous Substances None SARA Title III Section 313 Toxic Chemicals None present or none present in regulated quantities. California Proposition 65 This product contains the following chemical(s) listed by the State of California under The Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65) as being known to cause cancer, birth defects or other reproductive harm: None known WHMIS Not regulated by WHMIS. 16. Other Information Disclaimer The data contained herein is based upon information that Accumetric LLC believes to be Reliable. Users of this product have the responsibility to determine that suitability of use and to adopt all necessary precautions to ensure the safety and protection of property and persons involved in said use. All statements to suggestions are made without warranty, expressed or implied, regarding the accuracy of the information, the hazards connected with the use of the material or the results to be obtained from the use thereof.