![]() |
![]() |
![]() |
|
| Home > Products > Chemicals & Paint > MSDS Sheets > MSDS 6611 -- [Back] | |||
|
MSDS 6611 6611: Slik Pak Grease-2 Oz. Pouch [60]MSDS Last updated: 10/05/2009
Permatex, Inc.
10 Columbus Blvd.
Hartford, CT 06106 USA
Telephone; 1-87-Permatex
(877) 376-2839
Emergency: 800-255-3924
International Emergency: 813-248-0585
MATERIAL SAFETY DATA SHEET
1. PRODUCT IDENTIFICATION
Product Name: SLIK PAK 5TH WHEEL GREASE 4X60 2OZ
Item No: 01010
Product Type: Lubricant
2. COMPOSITION/INFORMATION ON INGREDIENTS
Component Weight% ACGIH; TLV-TWA OSHA PEL
LITHIUM-CALCIUM PETROLEUM >60 Not Listed Not Listed
GREASE BLEND MIXTURE
GRAPHITE <30 2 mg/m3 (respir) 15 mppcf TWA
7782-42-5 ACGIH
MOLYBDENUM DISULFIDE <5 10 mg/m3 15 mg/m3 (as
1317-33-5 (inhalable); 3 insoluble
mg/m3 (resp. as molybdenum)
insoluble
molybdenum)
SILICA, QUARTZ 0.1-1.0 0.05 mg/m3 0.1 mg/m3 TWA
14808-60-7 respirable
3. HAZARDS IDENTIFICATION
Toxicity: May cause eye, and skin irritation. If
ingested, will irritate esophagus and
stomach. May irritate respiratory system
upon frequent or prolonged use. This product
contains encapsulated silicon dioxide
(quartz silica). No exposure to free
respirable silica is anticipated during
normal use of this product. Silica may be
released by grinding or machining of coated
material. Use NIOSH-approved dust/mist
respirator when grinding or machining.
Primary Routes of Entry: Eye and skin contact, ingestion, inhalation
Signs and Symptoms of Exposure: Overexposure may cause eye and skin redness.
Ingestion may cause cramps or diarrhea.
Based on testing, this product is not likely
to be an inhalation hazard and is considered
to have a low order of acute toxicity.
Medical Conditions Recognized as Preexisting pulmonary and dermatological
Being Aggravated by Exposure: disorders.
Component Weight Percent NTP ACGIH IARC
Carcinogens
SILICA, QUARTZ 0.1-1.0 A2- Suspected Group 1;
14808-60-7 Human Monograph 68,
Carcinogen 1997
4. FIRST AID MEASURES
Ingestion: Do not induce vomiting. Slowly dilute with 1-2 glasses of
water or milk and seek medical attention. Never give
anything by mouth to an unconscious person.
Inhalation: Move to fresh air in case of accidental inhalation of
vapours.
Skin Contact: Wash off immediately with soap and plenty of water
removing all contaminated clothes and shoes. If skin
irritation persists, call a physician.
Eye Contact: In case of contact, immediately flush eyes with plenty of
water for at least 15 minutes and get medical attention
if irritation persists.
5. FIRE FIGHTING MEASURES
Flash Point °F(C°): 380°F. COC
Recommended Extinguishing Media: Carbon Dioxide, Dry Chemicals, Foam.
Special Fire-Fighting Procedures: Use water to cool exposed containers. Warm
stream directed into fire may cause frothing
with subsequent spread of flame. Firefighters
should wear self contained breathing
apparatus.
Hazardous Products of Combustion: Oxides of carbon
Unusual Fire/Explosion Hazards: None.
Lower Explosive Limit: Not determined.
Upper Explosive Limit: Not determined.
6. ACCIDENTAL RELEASE MEASURES
Spill Procedures: Absorb spill or leak with sand or cloth. Sweep or shovel into
an appropriate waste container until disposal. Prevent from entering waterways
or sewers.
7. HANDLING AND STORAGE
Storage: Store away from heat.
Handling: Avoid prolonged skin contact. Keep away from eyes. Wash hands and
face after handling this compound.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Eyes: Safety glasses.
Skin: Neoprene or nitrile gloves recommended.
Ventilation: General; local exhaust ventilation as necessary to
control any air contaminants to within their
exposure limits (or to the lowest feasible levels
when limits have not been established) during the
use of this product.
Respiratory Protection: Not required under normal use. In case of
insufficient ventilation, wear suitable respiratory
equipment.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Black semi-solid
Odor: Mild petroleum odor
Boiling Point: Not determined.
pH: Does not apply
Solubility in Water: Nil
Specific Gravity: 1.0
VOC Content (Wt. %): None
Vapor Pressure: Not determined
Vapor Density (Air=1): >1 (air=1)
Evaporation Rate: Negligible
10. STABILITY AND REACTIVITY
Chemical Stability: Stable at normal conditions
Hazardous Polymerization: WILL NOT OCCUR.
Incompatabilities: Strong oxidizers
Conditions to Avoid: Heat.
Hazardous Products of Combustion: Oxides of carbon
11. TOXICOLOGICAL INFORMATION
See Section 3
12. ECOLOGICAL INFORMATION
No data available
13. DISPOSAL CONSIDERATIONS
Recommended Method of Disposal:
Disposal should be made in accordance with federal, state and local
regulations..
US EPA Waste Number:
NH - Not a RCRA Hazardous Waste Material
14. TRANSPORTATION INFORMATION
DOT (49CFR 172)
Ground Transport (DOT)
DOT Shipping Name: Unrestricted
Hazard Class: None
UN/ID Number: None
Marine Pollutant: None
IATA
Proper Shipping Name: Not regulated
Class or Division: None
UN/ID Number: None
IMDG
Proper Shipping: Unrestricted
Hazard Class: None
UN Number: None
15. REGULATORY INFORMATION
SARA 313 Chemicals: The following component(s) is listed as a SARA Section 313
Toxic Chemical.
NONE
California Proposition 65:
No California Prop 65 chemicals are known to be present at or above the No
Significant Risk Level
TSCA Inventory Status:
Listed on Inventory: YES All components of this product are listed (or exempt)
on the EPA TSCA inventory.
16. OTHER INFORMATION
Estimated NFPA Rating: HEALTH 1, FLAMMABILITY 1, REACTIVITY 0.
Estimated HMIS Classification: HEALTH 1, FLAMMABILITY 1, PHYSICAL HAZARD 0
NFPA is a registered trademark of the National Fire Protection Assn.
HMIS is a registered trademark of the National Paint and Coatings Assn.
Prepared By: Denise Boyd, Manager-Environmental, Health & Safety
Company: Permatex. Inc. 10 Columbus Blvd. Hartford, CT USA 06106
Telephone No.: 1-87-Permatex (877) 376-2839
Revision Date: May 14, 2008
Revision Number: 5
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance. For more product information by email, click here Imperial Supplies LLC does not provide services and products outside the United States |