MSDS 6503

MSDS MATERIAL SAFETY DATA SHEET
The Blaster Corporation            "BLASTER"
             PB Penetrating Catalyst
MSDS Number: PB - Aerosol          Revision Date: 10/16/07

   1. PRODUCT AND COMPANY IDENTIFICATION


   Product Name:  PB Penetrating Catalyst
   Revision Date: 10/16/07
   MSDS Number:   PB - Aerosol
   Common Name:   PB Blaster
   Product Code:  16-PB, 8-PB, 8-PBS, 20-PB, 26-PB


   Manufacturer:  The Blaster Chemical Companies, Inc.
                  8500 Sweet Valley Drive
                  Valley View, Ohio 44125


                  (216) 901-5800
                  (216) 901-5801 fax
                  www.blasterproducts, com


   24 Hour emergency contact:     Chemtrec (800) 424-9300


   2. COMPOSITION/INFORMATION ON INGREDIENTS


   Hazardous Ingredients               CAS #      Percent     Exposure Limits


   Alkloxypolyethylenioxyethanol     68131-40-8    0-3 %      OSHA (TWA) - N/E
                                                              ACHIH (TLV) - N/E


   Solvent Naphtha, Heavy Aromatic** 64742-94-5    40-50%     OSHA (TWA) - N/E
                                                              ACGIH (TWA) - N/E


   Heavy Petroleum Distillate        64742-65-0    20-30%     OSHA (TWA) - N/E
                                                              ACGIH (TLV) - N/E


   Hydrotreated Light Distillate     64742-47-8 30-40%        OSHA (TWA) - N/E
                                                            ACGIH (PEL)-500 ppm


   *Denotes chemical is subject to the reporting requirements of SECTION 313 of
   Title III of the 1986 Super fund Amendments and Reauthorization Act (SARA)   
   and 40 CFR PART 372.
   **Aromatic Naphtha contains 1-7% Naphthalene (91-20-3) and 0-1% Pseudocumene
   (95-63-6)


   3. HAZARDS IDENTIFICATION


   Route of Entry:   Eyes, skin, inhalation, ingestion
   Target Organs:
   Inhalation:       Inhalation of spray mist may cause irritation to the
                     respiratory tract.
   Skin Contact:     Repeated or prolonged contact with skin may cause mild
                     irritation and possibly dermatitis.
   Eye Contact:      Likely to cause immediate or delayed irritation.           
                     Irritation will show as redness and/or swelling of the     
                     eyes.
   Ingestion:        Ingestion may cause irritation to the mouth, esophagus
                     and stomach.
                     May aggravate pre-existing skin and respiratory disorders.


   Notice: Reports have associated repeated and prolonged occupational
   overexposure to solvents with permanent brain and nervous system damage.   
   Intentional misuse by deliberately concentrating and inhaling the contents   
   may be harmful or fatal.


   4. FIRST AID MEASURES

   Inhalation:   Remove to fresh air. If not breathing, give artificial
                 respiration.
                 If breathing is difficult, give oxygen. Continue to monitor.
                 Get medial attention.
   Skin Contact: Remove contaminated clothing immediately! Wash skin with soap
                 and water.
                 If irritation develops, seek medical attention.
   Eye Contact:  Flush eye(s) with water for 15 minutes. Get medical attention.
                 If eye irritation persist, obtain medical treatment.
   Ingestion:    Do not induce vomiting! Get medical attention immediately!


   5. FIRE FIGHTING MEASURES


   Flash Point:  155 degrees F  ASTM D-56 (TCC)


   Extinguishing Media: Dry chemical, carbon dioxide or foam is recommended.
   Water may be ineffective for extinguishment, but can be useful in minimizing 
   or dispersing vapors, protecting personnel and cooling containers. If   
   containers are not properly cooled they can rupture in the heat of a fire.   
   Avoid spreading burning liquid with water used for cooling purposes.


   Unusual Fire & Explosion Hazards:  Level 3 Aerosols - Contents Under
   Pressure!


   6. ACCIDENTAL RELEASE MEASURES


   Leaking aerosol cans should be put into suitable container until the internal
   pressure has dissipated. Use suitable absorbents to collect liquid product.  
   Consult regulations for the disposal of the container, liquid and absorbents.


   7. HANDLING AND STORAGE


   Handling Precautions:   Use in accordance with good industrial workplace
                           practices. Avoid unnecessary contact. 
                           Wash thoroughly after handling.
                           Use with good ventilation.
   Storage Requirements:   Store in a dry place away from excessive heat.
                           Store containers with lids on and properly labeled.

                           Do not store at temperatures above 120 degrees F.


   8. EXPOSURE CONTROLS/PERSONAL PROTECTION


   Engineering Controls:   Eye wash stations and emergency showers should be
                           immediately available.
   Protective Equipment:   Eyes and Face: Standard safety glasses with splash
                           shields typically offer adequate protection. Where   
                           excessive splashing or spraying is possible, a face  
                           shield should be used.


             Skin and clothing: Excessive contact should be avoided.
             Neoprene gloves, boots and aprons will provide adequate
             protection when contact cannot be avoided.
             Remove and wash any contaminated clothing immediately.
             Wash thoroughly after handling.


             Respiratory: Good general ventilation should be
             sufficient to control airborne levels. Maintain airborne           
             concentrations below OSHA established exposure limits of           
            ingredients in Section 2.


   Exposure Guidelines/Other:  The Blaster Chemical Companies takes no
             responsibility for determining what measures are required for      
             personal protection in any specific application. This information  
             should be used with discretion.


   9. PHYSICAL AND CHEMICAL PROPERTIES


   Appearance:        Orange viscous oily
   Physical State:    Liquid                 Boiling Point:         352 F
   Odor:              Heavy aromatic         Freezing/Melting Pt:  Not          
                                                                   determined
   pH:                Not determined        Solubility:            nil
   Vapor Pressure:    Not determined        Spec Grav./Density:    0.87
                                                                   (water=1)
   Vapor Density:     >1 (air=1)


   Heat Value:           Not determined
   VOC:                  Not determined
   Evap. Rate:           <1 (NBA=1)
   Bulk Density:         Not determined
   Octanol:              Not applicable
   Molecular Weight:     Not determined
   Particle Size:        Not applicable
   Softening Point:      Not applicable
   Viscosity:            Not determined
   Percent Volatile:     Not determined
   Sat. Vap. Concentrat: Not determined
   Molecular Formula:    Not determined




  10. STABILITY AND REACTIVITY


   Stability:            This product is stable.
   Conditions to avoid:  Avoid excessive heat, sources of ignition and
                         excessive water.
   Materials to avoid (incompatibility):  Avoid contact with strong oxidizing
                         agents and strong reducing agents (strong acids or     
                         bases). Avoid mixture with water.
   Hazardous Decomposition products:  Carbon monoxide, carbon dioxide, and
                         various hydrocarbons.
   Hazardous Polymerization: Will not occur.


  11. TOXICOLOGICAL INFORMATION


   Toxicological information on this product as a mixture has not been
   determined. See section 15 for reportable ingredients.


  12. ECOLOGICAL INFORMATION


   Ecological information on this product as a mixture has not been determined.


  13. DISPOSAL CONSIDERATIONS


   Used or unused product should be disposed of in accordance with local, state,
   and federal regulations. Some special regulations may exist for the disposal
   of empty aerosol containers.


   Empty containers may contain residual pressure and contents. They should be
   handled with the same precautions as the product.


  14. TRANSPORT INFORMATION


   Dept. of Transportation (DOT);


   This product, as it leaves Blaster's facilities, meets the definitions set
   forth in CFR 49 part 173.150c as a "consumer commodity." Allowing for certain
   exceptions (173.156) for domestic surface (ground) shipments.


      Proper shipping name:  Consumer Commodity
      Hazard class:     ORM-D


      International (IMDT-IATA):


      Proper shipping name:  Aerosols, Limited Quantities
      Hazard class:          2 Flammable Compressed Gas
      UN Number:             1950


  15. REGULATORY INFORMATION


      COMPONENT / (CAS/PERC) / CODES


   *Distillates, petroleum, solvent-dewaxed heavy paraffinic 
   (64742650 40-60%) NJHS


   *Carbon dioxide (propellant) (124389 0-3%) MASS, OSHAWAC, PA, TXAIR


   REGULATORY KEY DESCRIPTIONS


   MASS = MA Massachusetts Hazardous Substances List
   OSHAWAC = OSHA Workplace Air Contaminants
   PA = PA Right-To-Know List of Hazardous Substances
   TXAIR = TX Air Contaminants with Health Effects Screening Level


  16. OTHER INFORMATION


   Manufacturer's Disclaimer:
   To the best of our knowledge, the information contained herein is accurate.
   However, neither The Blaster Chemical Companies nor any of its subsidiaries  
   assumes any liability whatsoever for the accuracy or completeness of the   
   information contained herein. Final determination of suitability of any   
   material is the sole responsibility of the user. All materials may present   
   unknown hazards and should be used with caution. Although certain hazards 
   are described herein, we cannot guarantee that these are the only hazard   
   which exists.


   HMIS Ratings:            NFPA Ratings:
   Health:        2         Health:       2
   Fire:          2         Fire:         2
   Reactivity:    0         Reactivity:   0


                 END OF MSDS DOCUMENT

The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance.

© 2010 Imperial Supplies LLC Questions or comments? Contact us.