![]() |
![]() |
![]() |
|
| Home > Products > Chemicals & Paint > MSDS Sheets > MSDS 5809 -- [Back] | |||
|
MSDS 5809 5809: Bandage Spray 3 Oz Bottle [2]MSDS Last updated: 01/15/2010
IMPERIAL SUPPLIES LLC MSDS SHEET FOR 5809
ARI
PO Box 510
Orchard Hill, GA 30266
Date: January 2005
SECTION 1 - PRODUCT IDENTIFICATION
MANUFACTURERS NAME: ARI
ADDRESS: PO BOX 510, ORCHARD HILL, GA 30266
EMERGENCY PHONE #: 800-241-5064
TRADE NAME: BANDAGE SPRAY
SYNONYMS: AEROSOL BANDAGE SPRAY
SECTION 2 - MATERIAL ANALYSIS / ACTIVE INGREDIENTS
Component or % of Mixture CAS # TLV
Material Chemical
Name
Benzocaine, USP 1.92 % 94-09-7 Not established
Benzethonium .12% 57-09-0 Not established
Chloride
PVP / VA E-335 8.64 25086-89-9 Not established
SDA 40-200 49.32 64-17-5 1000 ppm
A-46 Hydrocarbon 40.0% 68476-86-8 1000 ppm
SECTION 3 - PHYSICAL DATA
Boiling Point N/A
Solubility in H2O% by weight Disperses with water
Specific Gravity H2O = 1 1.35
Vapor pressure in can PSI at 70F 35
% Volatiles by Volume 78.0%
pH N/A
Appearance and Odor Colorless liquid.
SECTION 4 - FIRE AND EXPLOSION DATA
Flash Point (Closed cup) N/A
Flammable Explosive Limits (% volume Lower: N/A
in air) Upper: 120F
Extinguishing Methods Dry chemical or CO2
Special fire and Explosion Procedures Cool containers with water if exposed
Unusual Fire and Explosion Hazard Product packaged in aerosol form, will
explode under extreme heat.
SECTION 5 - HEALTH AND HAZARD INFORMATION
HEALTH HAZARD DATA
ROUTES OF EXPOSURE
Inhalation May irritate upper respiratory tract and cause
numbness.
Skin Contact Mildly irritating
Eye Contact Spray can cause pain and general inflammation.
Ingestion May cause irritation and vomiting.
Effects of Based on available data, repeated exposures are not
Overexposure anticipated to cause any significant adverse effects.
EMERGENCY AND FIRST AID PROCEDURES
Eye Flush with large amounts of water, lifting upper lids.
Skin Wash areas with soap and water
Ingestion Rinse mouth, and consult a physician.
Inhalation Remove to fresh air
SECTION 6 -REACTIVITY DATA
Condition contributing to instability Stable under normal storage
conditions
Incompatability Strong oxidizing agents or reducing
agents.
Hazardous decomposition products Oxides of carbon, aldehides, and
acids.
Conditions contributing to hazardous Will not occur.
polymerization
SECTION 7 - SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED
Neutralizing Flush spill area with water
chemical
Waste disposal Dispose of in accordance with state, local and federal
method regulations
SECTION 8 - INDUSTRIAL HYGIENE CONTROL MEASURES
Ventillation Good general ventilation should be sufficient for most
Requirements conditions.
SPECIFIC PERSONAL PROTECTIVE EQUIPMENT
Respiratory (specific in detail) None Required.
Eye None Required.
Gloves None Required.
Other Clothing and Equipment None Required.
SECTION 9 -SPECIAL PRECAUTIONS
Precautionary Statements Packaged under pressure. Do not
puncture, incincerate or store above
120F. Flammable. Keep away from heat
source.
Other Handling and Storage Store in well ventilated areas, away
Requirements from heat, direct sunlight and sources
of ignition. Keep away from oxidizing
agents. Containers should not be
dropped. Install protective caps for
shipment.
Department of Transportation
Information
PROPER SHIPPING NAME:
HAZARD CLASS:
CONSUMER COMMODITY
ORM-D
Prepared by: ARI DATE: January 2004
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance. For more product information by email, click here Imperial Supplies LLC does not provide services and products outside the United States |