Start an Order |
|
|
|
| Start an Order |
|||
| Home > Products > Chemicals & Paint > MSDS Sheets > MSDS 5201 -- [Back] | |||
|
MSDS 5201 5201: (DISCONTINUED)5201-4: Premium Sorbent Pad Univ 16X18 [100] MSDS Last updated: 03/04/2010
MATERIAL SAFETY DATA SHEET
SPILFYTER® Products Page1 of 5
G Series Sorbents Revision Date: 02/20/08
MSDS No. 1005
Section 1. Chemical Product and Company Identification
Product Number: G series
Product Name: GENERAL PURPOSE Sorbent Products
Manufacturer: Emergency Telephone Number:
NPS Corporation CHEMTREC-Domestic (800)424-9300 24
hours
3303 Spirit Way -International
(202)483-7616 24 hours
Green Bay, WI 54303 Information (800) 558-5066
7:30am-4:30pm CDT M-F
Section 2. Composition/Information on Ingredients
CAS Registry # Component
9003-07-0 Polypropylene 98.4%
Particulate or Fabric
N/A Green Pigment 0.3%
NA Blue Pigment 0.3%
557-11-F Surfactant 1.0%
(NOTE: See Section 8 of this MSDS for Exposure Guidelines)
Section 3. Hazards Identification
Emergency Overview: Odorless, white or colored fabric
or particulate. This material
presents little or no hazard
spilled and exhibits no unusual
fire hazard.
Potential Health Effects
Eye: Direct contact may cause
irritation.
Inhalation: Exposure to dust levels exceeding
the PEL (see Section 8) may cause
irritation of the upper respiratory
system. Breathing dust may
aggravate acute or chronic asthma
or other chronic pulmonary
diseases.
Signs and Symptoms:
Eyes: Redness, tearing
Inhalation: Dry cough, labored breathing during
exertion
SECTION 4. First Aid Measures
Eyes: Immediately flush with plenty of
water for at least 15 minutes. If
irritation persists, seek medical
attention.
Skin: Brush off excess fibers with dry
towel. Wash affected area with
plenty of soap and water for
several minutes. If skin irritation
develops or persists, seek medical
attention:
Inhalation: Remove to fresh air. If not
breathing, give artificial
respiration. If breathing is
difficult, give oxygen. Seek
medical attention.
NOTE: If burned through contact with molten material, cool as quickly as
possible with water and seek medical attention. Do not attempt to remove
the cooled molten material.
Section 5. Fire Fighting Measures
Flash Point: >625 F
Flammable Limits: NA
Auto-ignition Temperature: >675 F
NOTE: This material will burn, but it is difficult to ignite.
Extinguishing Media: Water spray, ABC dry chemical, foam
or carbon dioxide. Use water fog or
spray to cool exposed equipment and
containers.
Special Fire Fighting Procedures: For large fires or fires in
confined areas, full emergency
equipment with self-contained
breathing apparatus and full
protective clothing should be used.
Thermal decomposition of this
product may produce hazardous and
irritating gases. See Section 10.
Section 6. Accidental Release
Measures
Unused material can be shoveled, swept, or vacuumed and recycled for
use. Avoid generating airborne dust.
If used material is released or spilled, see Section 13.
Section 7. Handling and Storage
Store at room temperature in a dry area. When handling, avoid the
generation of airborne dust. Storage for extended periods (>30 days) at
temperatures >150 F may cause decomposition. This material produces an
electrostatic accumulation hazard. Use proper grounding/bonding
procedures.
Section 8. Exposure Controls/Personal Protection
Exposure Limits: None specifically developed for
this product; treated as a nuisance
dust as defined in 29 CRF
1910.1000.
OSHA PEL: Total Dust is 15 mg/M3.
Respirable Fraction is 5mg/M3.
ACGIH TLV is 10 mg/M3.
The end-user must determine the specific types of personal protective
equipment needed according to 29 CFR 1910.132-Personal Protective
Equipment (PPE) for General Industry. The following are only
suggestions:
Eyes: Safety glasses or goggles
Skin: Work gloves
Adequate ventilation should be
provided to limit the amount of
airborne dust.
Section 9. Physical and Chemical
Properties
Appearance: White or colored fabric or
particulate
Odor: Odorless
Boiling Point: NA
Vapor Pressure (mmHg): NA
Vapor Density: NA
Solubility in Water: Insoluble
Specific Gravity (H2O=1): 0.90
Melting Point: >320 F
pH: NA
Evaporation Rate(Butyl Acetate=1): NA
% Vaporizable by volume (H2O=100): <0.4
Section 10. Stability and
Reactivity
Stable: Yes
Conditions to Avoid: See Section 7
Incompatibility (Materials to Avoid contact with hot or
Avoid): concentrated nitric and perchloric
acids, and fuming sulfuric acid at
temperatures >140 F
Hazardous Decomposition or Thermal decomposition produces
Byproducts: carbon monoxide, carbon dioxide,
methane, acetone and other ketones.
Hazardous Polymerization: Will not occur
Section 11. Toxicological
Information
This product is not listed by NTP or IARC. See Section 15.
Section 12. Ecological Information
No data available. See Section 15.
Section 13. Disposal Considerations
This product in itself is considered to be non-hazardous as defined by
RCRA (40 CRF 261). Once used, this product will take on the
characteristics of the chemical sorbed and should be disposed of
accordingly. Disposal of this product (used or unused) must be in
compliance with all local, state, and federal regulations.
Section 14. Transport Information
This product is not a DOT Hazardous Material and is not regulated for
all shipping purposes.
Section 15. Regulatory Information
This product does not meet the
definition of a hazardous chemical
given in 29 CFR 1910.1200 (OSHA).
TSCA Inventory Status: All components are listed on the
TSCA list.
SARA Title III
Section 302 Extreme Hazardous Not listed
Substance List:
Section 311/312 Hazardous
Classification:
Immediate (acute): No
Delayed (chronic): No
Fire: No
Sudden Release of Pressure: No
Reactive: No
Section 313 Toxic Chemicals: Not listed
USEPA CERCLA-Reportable Quantity Not listed
(RQ):
RCRA Hazardous Waste: Not listed
State/Int'l Right-to-Know Not listed
Regulations:
Section 16. Other Information
Abbreviations:
CFR: Code of Federal Regulations
OSHA: Occupational Safety and Health
Administration
MSDS: Material Safety Data Sheet
PEL: Permissible Exposure Limit
NA: Not Applicable
ACGIH: American Conference of Governmental
Industrial Hygienists
TLV: Threshold Limit Value
NTP: National Toxicology Program
IARC: International Agency for Research
on Cancer
RCRA: Resource Conservation and Recovery
Act
TSCA: Toxic Substances Control Act
SARA: Superfund amendments and
Reauthorization Act
USEPA: United States Environmental
Protection Agency
CERCLA: Comprehensive Response,
Compensation, and Liability Act
DOT: Department of Transportation
NFPA: National Fire Protection
Association
HMIS: Hazardous Material Information
System
NFPA Ratings: HMIS Ratings:
Health: 0 Health: 0
Fire: 1 Flammability: 1
Reactivity: 0 Reactivity: 0
Special Hazard: None Personal Protection: NA
NOTE: This MSDS has been prepared only for the GENERAL PURPOSE Sorbent
Products (G Series) of SPILFYTER® Products. The MSDS's of the chemicals
used with this product must be reviewed completely, and precautions
taken as described.
The information accumulated herein has been compiled from sources
believed to be reliable and is accurate to the best of our knowledge.
However, NPS Corporation cannot give guarantees regarding the
information from sources, and expressly does not make any warranties,
nor assumes any liability for its uses of this product.
Disclaimer
You have purchased SPILFYTER® products from NPS Corporation
You have been provided data, product labels, MSDS's and other
information about SPILFYTER® Products.
Some SPILFYTER® Products are hazardous. Information about SPILFYTER®
Products that are hazardous is furnished without guarantee. NPS
Corporation does not guarantee the accuracy of the information about
hazardous SPILFYTER® Products.
Those products are only to be used by people having expertise in using
the hazardous products.
The Information provided about the hazardous products is believed to be
correct. You must perform your investigation as to the safety, toxicity,
suitability, and proper shipping method for any hazardous SPILFYTER®
Product.
No guarantee, expressed or implied, is made by NPS Corporation about the
results of use of its products. No guarantee is made as to the safety
and toxicity of any SPILFYTER® Product.
NPS Corporation does not assume any liability arising out of use of
SPILFYTER® Products. Additional information and research may be
necessary before you use the SPILFYTER® Products. NPS Corporation is not
responsible for damages, direct or indirect, resulting from the use of
SPILFYTER® Products or from reliance on data in the MSDS or product
label.
If you resell SPILFYTER® Products, you must by law, furnish your
customers a copy of MSDS's and handling instructions.
You are also required by law to insure that all SPILFYTER® Products are
properly shipped.
SPILFYTER® KOLLECT-A-KEM®, HANDS-IN-BAG®, KOLORSAFE®, and GRAB&GO® are
all registered trademarks of NPS Corporation
AQUALOCKIT , TRUK-KIT, DRIANGUARD, GAPSEAL, MEDICLEAN, and TIDYMAT are
all trademarks of NPS Corporation
Copyright 2001, NPS Corporation
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance. For more product information by email, click here Imperial Supplies LLC does not provide services and products outside the United States |
