Start an Order |
|
|
|
| Start an Order |
|||
| Home > Products > Chemicals & Paint > MSDS Sheets > MSDS 5200 -- [Back] | |||
|
MSDS 5200 5200: (DISCONTINUED)5205: Sorbent Sock 3" X 4' Oil Only [15] 5206: Sorbent Sock 3" X 10' Oil Only [6] 5210: Green Replacement Len For 5023 [1] 5211: Drum Top Pad / Green-Gen Purp [25] 5211-1: Drum Top Pad / Green [10] 5212: (DISCONTINUED) 5213: (DISCONTINUED) 5220: 1 Spill Kit / White [1] 5220-4: 4 Spill Kits / White [4] MSDS Last updated: 03/08/2010
IMPERIAL SUPPLIES LLC MSDS SHEET FOR 5205
SPILFYTER Products
M Series Sorbents
Revision Date: 2/20/2008
MSDS No. 1012
SECTION 1. CHEMCIAL PRODUCT AND COMPANY IDENTIFICATION
Product Number: M Series
Product Name: PREMIUM OIL ONLY Sorbent Products
Manufacturer Emergency Telephone Numbers:
NPS Corporation CHEMTREC-Domestic (800)424-9300 24 hrs
3303 Spirit Way International (202) 483-7616 24 hrs
Green Bay, WI 54304 Information (800) 558-5066 7:30am-4:30pm CDT M-F
SECTION 2. COMPOSITION/INFORMATION ON INGREDIENTS
CAS Registry # Component
9003-07-0 Polypropylene Particulate or 99.7%
Fabric 0.3%
Blue Pigment
(NOTE: See Section 8 of this MSDS for Exposure Guidelines)
SECTION 3. HAZARDS IDENTIFICATION
Emergency Overview
Odorless, white or colored fabric or particulate. This material presents
little or no hazard if spilled and exhibits no unusual fire hazard.
Potential Health Effects
Eye: Direct contact may cause irritation.
Inhalation: Exposure to dust levels exceeding the PEL (see section 8)
may cause irritation of the upper respiratory system.
Breathing dust may aggravate acute or chronic asthma or
other chronic pulmonary diseases.
Signs and Eyes: Redness, Tearing
symptoms: Inhalation: Dry cough, labored breathing during exertion
SECTION 4. FIRST AID MEASURES
Eyes: Immediately flush with plenty of water for at least 15 minutes. If
irritation persists, seek medical attention.
Skin: Brush off excess fibers with dry towel. Wash affected area with
plenty of soap and water for several minutes. If skin irritation
develops or persists, seek medical attention.
Inhalation Remove to fresh air. If not breathing, give artificial respiration.
: If breathing is difficult, give oxygen. Seek medical attention.
NOTE: If burned through contact with molten material, cool as quickly as
possible with water and seek medical attention. Do not attempt to
remove the cooled molten material.
SECTION 5. FIRE FIGHTING MEASURES
Flash Point: >625 F
Flammable Limits: NA
Auto-ignition >675 F
Temperature:
NOTE: This material will burn, but it is difficult to ignite
Extinguishing Water spray, ABC dry chemical, foam or carbon dioxide. Use
Media: water fog or spray to cool exposed equipment and
containers.
Special Fire For large fires or fires in confined areas, full emergency
Fighting equipment with self-contained breathing apparatus and full
Procedures: protective clothing should be used. Thermal decomposition
of this product may produce hazardous and irritating gases.
See Section 10.
SECTION 6. ACCIDENTAL RELEASE MEASURES
Unused material can be shoveled, swept or vacuumed and recycled for use. Avoid
generating airborne dust.
If used material is released or spilled, see Section 13.
SECTION 7. HANDLING AND STORAGE
Store at room temperature in a dry area. When handling, avoid the generation
of airborne dust. Storage for extended periods (>30 days) at temperatures >150
F may cause decomposition. This material produces an electrostatic
accumulation hazard. Use proper grounding/bonding procedures.
SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Exposure None specifically developed for this product; treated as a
Limits: nuisance dust as defined in 29 CFR 1910.1000.
OSHA PEL: Total Dust is 15 mg/M3
Respirable Fraction is 5mg/M3
ACGIH TLV is 10 mg/M3.
The end-user must determine the specific types of personal protective
equipment needed according to 29 CFR 1910.132-Personal Protective Equipment
(PPE) for General Industry. The following are only suggestions:
Eyes: Safety glasses or goggles
Skin: Work gloves
Adequate ventilation should be provided to limit the amount of airborne dust.
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: White or colored fabric or particulate
Odor: Odorless
Boiling Point: NA
Vapor pressure (mmHg): NA
Vapor Density: NA
Solubility in Water: Insoluble
Specific Gravity (H2O=1): 0.90
Melting Point: >320 F
pH: NA
Evaporation Rate (Butyl Acetate=1): NA
% Vaporizable by volume (H2O=100): <0.4
SECTION 10. STABILITY AND REACTIVITY
Stable: Yes
Conditions to Avoid: See Section 7
Incompatibility Avoid contact with hot or concentrated nitric and
(Materials to Avoid): perchloric acids, and fuming sulfuric acid at
temperatures >140 F
Hazardous Thermal decomposition produces carbon monoxide, carbon
Decomposition or dioxide, methane, acetone and other ketones.
Byproducts:
Hazardous Will not occur
Polymerization:
SECTION 11. TOXICOLOGICAL INFORMATION
This product is not listed by NTP or IARC. See Section 15.
SECTION 12. ECOLOGICAL INFORMATION
No data available. See Section 15.
SECTION 13. DISPOSAL CONSIDERATIONS
This product in itself is considered to be non-hazardous as defined by RCRA
(40 CFR 261). Once used, this product will take on the characteristics of the
chemical sorbed and should be disposed of accordingly. Disposal of this
product (used or unused) must be in compliance with all local, state and
federal regulations.
SECTION 14. TRANSPORT INFORMATION
This product is not a DOT Hazardous Material and is not regulated for all
shipping purposes.
SECTION 15. REGULATORY INFORMATIN
This product does not meet the definition of a hazardous chemical given in 29
CFR 1910.1200 (OSHA).
TSCA Inventory Status: All components are listed on the TSCA list.
SARA Title III
Section 302 Extreme Hazardous Substance List: Not listed
Section 311/312 Hazaard Classification:
Immediate (acute): No
Delayed (chronic): No
Fire: No
Sudden Release of Pressure: No
Reactive: No
Section 313 Toxic Chemicals: Not listed
USEPA CERCLA-Reportable Quantity (RQ): Not listed
RCRA Hazardous Waste: Not listed
State/Int'l Right-to-Know Regulations: Not listed
SECTION 16. OTHER INFORMATINO
Abbreviations:
CFR: Code of Federal Regulations
OSHA: Occupational Safety and Health Administration
MSDS: Material Safety Data Sheet
PEL: Permissible Exposure Limit
NA: Not Applicable
ACGIH: American Conference of Governmental Industrial Hygienists
TLV: Threshold Limit Value
NTP: National Toxicology Program
IARC: International Agency for Research on Cancer
RCRA: Resource Conservation and Recovery Act
TSCA: Toxic Substances Control Act
SARA: Superfund Amendments and Reauthorization Act
USEPA: United State Environmental Protection Agency
CERCLA: Comprehensive Response, Compensation and Liability Act
DOT: Department of Transportation
NFPA: National Fire Protection Association
HMIS: Hazardous Material Information System
NFPA RATINGS: HMIS RATINGS:
Health: 0 Health: 0
Fire: 1 Flammability: 1
Reactivity: 0 Reactivity: 0
Special Hazard: None Personal Protection: NA
NOTE: This MSDS has been prepared only for the Premium Oil Only Sorbent
Products (M Series) of SPILFYTER Products. The MSDS's of the chemicals used
with this product must be reviewed completely and precautions taken as
described.
The information accumulated herein has been compiled from sources believed to
be reliable and is accurate to the best of our knowledge. However, NPS
Corporation cannot give guarantees regarding the information from sources, and
expressly does not make any warranties, nor assumes any liability for its uses
of this product.
Disclaimer
You have purchased SPILFYTER products from NPS Corporation
You have been provided data, product labels, MSDS's and other information
about SPILFYTER Products.
Some SPILFYTER Products are hazardous. Information about SPILFYTER Products
that are hazardous is furnished without guarantee. NPS Corporation does not
guarantee the accuracy of the information about hazardous SPILFYTER Products.
Those products are only to be used by people having expertise in using the
hazardous products.
The information provided about the hazardous products is believed to be
correct. You must perform your investigation as to the safety, toxicity,
suitability and proper shipping method for any hazardous SPILFYTER product.
No guarantee, expressed or implied, is made by NPS Corporation about the
results of use of its products. No guarantee is made as to the safety and
toxicity of any SPILFYTER Product.
NPS Corporation does not assume any liability arising out of use of SPILFYTER
Products. Additional information and research may be necessary before you use
the SPILFYTER Products. NPS Corporation is not responsible for damages, direct
or indirect, resulting from the use of SPILFYTER Products or from reliance on
data in the MSDS or product label.
If you resell SPILFYTER Products, you must by law furnish your customers a
copy of MSDS's and handling instructions.
You are also required by law to insure that all SPILFYTER Products are
properly shipped.
SPILFYTER KOLLECT-A-KEM, HANDS-IN-BAG, KOLORSAFE, and GRAB&GO are all
registered trademarks of NPS Corporation.
AQUALOCKIT, TRUK-KIT, DRAINGUARD, GAPSEAL, MEDICLEAN and TIDYMAT are all
trademarks of NPS Corporation.
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance. For more product information by email, click here Imperial Supplies LLC does not provide services and products outside the United States |
